Daikin Industries, Ltd.

Yukari Yamamoto

Tadaharu Isaka

Hayato Tsuda

Yumi Zenke

Hiroyuki Hamada

Yasuyuki Yamaguchi

Takahisa Aoyama

Keizou Shiotsuki

Provided is a pipe joint including a cylindrical hollow, wherein the wall thickness of a part having the largest wall thickness of the pipe joint is 2 to 7 mm, the ratio of the length of the hollow in the axial direction (L) to the diameter of the hollow (D), (L/D), is 5 or less, the pipe joint contains a copolymer containing tetrafluoroethylene unit and a fluoro(alkyl vinyl ether) unit, the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 2.8 to 6.0% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 4.0 g/10 min or higher and lower than 11.0 g/10 min, and the number of functional groups of the copolymer is 50 or less.

Pipe joint and manufacturing method of pipe joint

Provided is an injection molded article containing a copolymer containing tetrafluoroethylene unit and a fluoro(alkyl vinyl ether) unit, wherein the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 4.7 to 7.0% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 11.0 to 22.0 g/10 min, the melting point of the copolymer is 296 to 305° C., and the amount of fluorine ions dissolving out from the injection molded article into water is 7,500 μg/mor lower.

Injection-molded body and production method therefor

Provided is an injection molded article containing a copolymer containing tetrafluoroethylene unit and a fluoro(alkyl vinyl ether) unit, wherein the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 3.9 to 4.8% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 11.0 to 19.0 g/10 min, the melting point of the copolymer is 296 to 305° C., and the amount of fluorine ions dissolving out from the injection molded article into water is 7,500 μg/mor lower.

There is provided an injection molded article obtained by injection molding a copolymer using a mold provided with a gate, wherein the copolymer contains tetrafluoroethylene (TFE) unit and a fluoro(alkyl vinyl ether) (FAVE) unit, the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 5.2 to 6.3% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 19.0 to 35.0 g/10 min, the number of functional groups of the copolymer is 50 or less per 10main-chain carbon atoms, and the injection molded article has a gate section corresponding to the gate of the mold, and the ratio of the maximum flow length (a) from the gate section of the injection molded article to the average value (b) of the product thickness on the maximum flow length, ((a)/(b)), is 80 to 200.

Provided an injection molded article obtained by injection molding a copolymer using a mold provided with a gate, wherein the copolymer contains tetrafluoroethylene (TFE) unit and a fluoro(alkyl vinyl ether) (PAVE) unit, the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 3.5 to 4.7% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 22.0 to 35.0 g/10 min, the number of functional groups of the copolymer is 20 or less per 10main-chain carbon atoms, and the injection molded article has a gate section corresponding to the gate of the mold, and the ratio of the maximum flow length from the gate section of the injection molded article (a) to the average value of the product thickness on the maximum flow length (b), ((a)/(b)), is 80 to 200.

A member for a non-aqueous electrolyte battery containing a copolymer containing a tetrafluoroethylene unit and a fluoroalkyl vinyl ether unit, in which the number of functional groups per 10carbon atoms of a main chain of the copolymer is 100 or less, and a melt flow rate of the copolymer is less than 20 g/10 minutes.

Member for nonaqueous electrolyte batteries

Provided is an injection molding method for obtaining an injection molded article using an injection molding machine by means of filling a mold cavity of a mold with a molten copolymer from a nozzle of the injection molding machine, wherein the minimum thickness of the mold cavity is 0.8 mm or less, the total projected area of the mold is 1 cmor more, and the copolymer is a copolymer containing a tetrafluoroethylene unit and a fluoroalkyl vinyl ether unit, wherein the number of functional groups is 100 or less per 10main-chain carbon atoms of the copolymer.

Growing community of inventors

Osaka, Japan

Yukari Yamamoto