Huawei Digital Power Technologies Co., Ltd.

Yuanjun Liu

Ken Chin

Shanglin Mo

Zhixiang Hu

Wei Zhang

Shuaibing Wang

Guiping Zhang

Liangyun Kang

A power supply apparatus includes a totem-pole power factor correction (PFC) circuit and a control apparatus, and the totem-pole PFC circuit includes a first switching transistor and a second switching transistor. The control apparatus includes a controller and a dead time detection circuit, and the dead time detection circuit includes a detection capacitor and a detection resistor. A first end of the detection capacitor is connected to a first reference point, a second end of the detection capacitor is connected to a first end of the detection resistor, and a second end of the detection resistor is grounded. The controller is configured to, respectively, control an on/off status of the first switching transistor and an on/off status of the second switching transistor based on a voltage of the detection resistor and polarity of a voltage input by an alternating current input source.

Power supply apparatus and totem-pole PFC circuit control method

A high power factor rectifier circuit includes a totem pole power factor correction (PFC) circuit, a sampling resistor, a power suppl a PFC controller, and a filter. The totem pole PFC circuit includes two bridge arm units connected in parallel between a first parallel connection point and a second parallel connection point. One end of the sampling resistor is connected to the first parallel connection point and a first reference ground, and the other end of the sampling resistor is separately connected to a sampling voltage input terminal of the PFC controller and a second reference ground. A grounding terminal of the PFC controller is connected to the first reference ground. A power output terminal of the power supply is connected to a power input terminal of the PFC controller using the filter.

High power factor rectifier circuit and power converter

A power factor correction (PFC) circuit includes an alternating current input circuit, a totem-pole PFC circuit, an input sampling circuit, an output sampling circuit, and a PFC control protection circuit. A first output terminal of the alternating current input circuit is respectively connected to a first input terminal of the totem-pole PFC circuit and a first input terminal of the input sampling circuit.

Power factor correction circuit and power converter

This application provides a resonant conversion system, including a controller and a resonant conversion circuit. The resonant conversion circuit includes a high frequency chopper circuit, a resonant cavity, a transformer, and a rectification filter network, and the high frequency chopper circuit includes switches Sand S. The controller is configured to: detect a bridge arm midpoint voltage V, and determine based on the Va current threshold signal used to indicate a current threshold; detect a resonant current on a primary side of the transformer, and compare the resonant current with the current threshold signal to control on/off of the switch Sor Sbased on the second electrical signal, so that the system operates in an inductive mode to ensure zero voltage switching of the switch, while operating in a state close to a capacitive mode to maximize the use of a gain region.

Resonant conversion system and control method

The control system includes a PFC circuit and a sampling control circuit, and the PFC circuit includes an inductor, a first power supply drive circuit, and a first bridge arm and a second bridge arm that are connected in parallel, and a first bridge arm midpoint is a serial connection point between a first upper bridge arm and a first lower bridge arm of the first bridge arm. The sampling control circuit is configured to control, based on voltages of two ends of an alternating current power supply, the first lower bridge arm to be turned on, so that the first power supply drive circuit starts charging. The sampling control circuit is further configured to: when charging duration of the first power supply drive circuit reaches first target duration, control the first lower bridge arm to be turned off, so that the first power supply drive circuit completes charging.

System and method for controlling totem pole power factor correction circuit, and power adapter

A pin state configuration circuit, a method for configuring pin states and an electronic device for configuring pin states are provided. The pin state configuration circuit includes a configured resistor load, a voltage sampling unit, and a comparator. The voltage sampling unit supplies a reference voltage to the configured resistor load by using a first or second configuration pin, and respectively samples voltages of the first and second configuration pins. The comparator calculates a first voltage ratio based on the voltage of the first configuration pin and the voltage of the second configuration pin, calculates a second voltage ratio based on the voltage of the first configuration pin and the voltage of the second configuration pin, and determines a corresponding pin configuration state based on the first and second voltage ratios. In this way, N&#xd7;N pin configuration states may be obtained by configuring two configuration pins.

Growing community of inventors

Shenzhen, China

Yuanjun Liu