Toyota Jidosha Kabushiki Kaisha

Iwatani Corporation

Yoshihiro Hori

Takayoshi Doi

Hiroaki Nemoto

Toshiyuki Kondo

Masao Okumura

Shotaro Ishikawa

Sozaburo Ohashi

Yoshito Endo

Noriaki Ishihara

Hideyo Omori

Yasuyuki Ueyama

Yoshito Endou

Yuu Matsuno

Provided is a pressure testing method for a high-pressure tank capable of avoiding a destruction of the high-pressure tank during a pressure test. A pressure testing method includes: extracting a plurality of AE waveforms from output waveforms of an AE sensor while increasing a pressure inside the high-pressure tank; and testing the high-pressure tank based on the extracted plurality of AE waveforms. The method includes: while increasing the pressure inside the high-pressure tank, classifying the extracted AE waveforms into first waveforms and second waveforms with a classifier that is machine-learned so as to classify the plurality of AE waveforms into the first waveforms derived from a macrocrack that increases immediately before destruction of the high-pressure tank, and the second waveforms derived from a microcrack smaller than the macrocrack; and stopping pressurization of the high-pressure tank based on the number of the first waveforms.

Pressure testing method and pressure tester

A pressure testing method capable of determining with a higher accuracy whether a high-pressure tank is deteriorated. The pressure testing method tests the high-pressure tank that includes a liner and a fiber-reinforced resin layer covering the outer surface of the liner and that has been used while repeating charge and discharge of gas to and from the inside thereof after undergoing a pressure resistance test conducted at a pressure resistance test pressure. The method increases the internal pressure of the high-pressure tank filled with gas to a test pressure that is lower than the pressure resistance test pressure, so that a plurality of AE waveforms is extracted from output waveforms of an AE sensor that detects AE waves generated in the high-pressure tank, and determines whether the high-pressure tank is deteriorated, on the basis of the extracted AE waveforms.

A lower die has a first lower-die edge extending along the outline shape of a sheet material, and a plurality of second lower-die edges disposed vertically below the first lower-die edge and each extending in a direction traversing an offcut of a sheet base material that is left behind after the sheet material is punched out. An upper die has a first upper-die edge which extends along the first lower-die edge and between which and the first lower-die edge the sheet base material is shorn to punch out the sheet material, and a plurality of second upper-die edges which is provided so as to be protrusible to vertically below the second lower-die edges and between which and the second lower-die edges the offcut is shorn and divided.

Cutting device and sheet material manufacturing method

A manufacturing method of porous layer comprises: drying a mixed solution containing conductive carbon powder and water-repellent resin powder by a spray-drying method, so as to produce a powdery substance including the conductive carbon powder coated with the water-repellent resin powder; and producing the porous layer from the powdery substance. Water-vapor permeability of the porous layer measured in conformity with the Japanese Industrial Standard ES-Z-0208 is 10000 to 25000 g/m&#xb7;24 h under conditions of temperature of 40&#xb0; C. and relative humidity of 90% RH.

Porous layer and manufacturing method of the same

A core-shell catalyst with high platinum mass activity for a short period of time. The method for producing a core-shell catalyst may comprise a core containing palladium and a shell containing platinum and coating the core, the method comprising: a step of preparing a copper-coated palladium-containing particle dispersion in which copper-coated palladium-containing particles are dispersed, the particles being palladium-containing particles coated with copper; a step of preparing a platinum ion-containing solution; a step of preparing a microreactor; and a substitution step of forming the shell by substituting the copper on the copper-coated palladium-containing particle surface with platinum by mixing the copper-coated palladium-containing particle dispersion and the platinum ion-containing solution in the microreactor.

Method for producing core-shell catalyst

A catalyst ink for improving the performance of catalyst electrodes in a fuel cell is produced by the following procedure. A catalyst dispersion is prepared by dispersing catalyst-supported particles as conductive particles with a catalyst supported thereon in a solvent. A gel material having viscoelasticity is prepared by mixing an ionomer with a volatile solvent. A catalyst ink having a desired viscosity is produced by stirring and mixing the catalyst dispersion with the gel material.

Manufacturing method of catalyst ink, manufacturing method of fuel cell, and fuel cell

A suction method that sucks inside of a filling nozzle used for supply of hydrogen by using a suction nozzle that is engaged with the filling nozzle, the suction method comprising: evacuating a vacuum chamber by using a vacuum pump; and sucking inside of the suction nozzle by using the evacuated vacuum chamber.

Suction device and suction method

A production method of a porous layer material for forming a porous layer includes the steps of obtaining particles that contain carbon and a water-repellent resin by spray drying a mixed solution that includes the carbon and the water-repellent resin, producing a paste that includes the particles, and extruding or rolling the paste to obtain the porous layer material in a sheet-like form.

Production method of porous layer material and production method of membrane electrode and gas diffusion layer assembly including porous layer material

A first layered article () in which a first electrolyte membrane () and an anode-side catalyst layer () are laminated, and a second layered article () in which a second electrolyte membrane () and a cathode-side catalyst layer () are laminated, are formed. Then, the first layered article () and the second layered article () are disposed so that the electrolyte membrane-side surfaces of the two articles face each other. A reinforcement frame () is then disposed between the two articles. The whole layered assembly in this state is thermocompression-bonded. Thus, a membrane-electrode assembly () in which the reinforcement frame () is embedded within an electrolyte membrane () that is formed by the fusion of first electrolyte membrane () and the second electrolyte membrane () is obtained.

Growing community of inventors

Nisshin, Japan

Yoshihiro Hori