Applied Materials, Inc.

Yijun Liu

Li-Qun Xia

Bo Xie

Ruitong Xiong

Kang Sub Yim

Sure Ngo

Hichem M'Saad

Huiwen Xu

Ning Li

Mark Joseph Saly

Xianmin Tang

Deenesh Padhi

Mihaela A Balseanu

Bhaskar Jyoti Bhuyan

Derek R Witty

Hang Yu

Michael Wenyoung Tsiang

Chad Peterson

Chengyu Liu

Zhelin Sun

Kevin Hsiao

Yichuen Lin

Xiaobo Li

Lin Yang

Exemplary semiconductor processing methods may include providing a silicon-containing precursor to a processing region of a semiconductor processing chamber. A substrate may be disposed within the processing region of the semiconductor processing chamber. The methods may include forming a plasma of the silicon-containing precursor in the processing region. The plasma may be at least partially formed by an RF power operating at between about 50 W and 1,000 W, at a pulsing frequency below about 100,000 Hz, and at a duty cycle between about 5% and 95%. The methods may include forming a layer of material on the substrate. The layer of material may include a silicon-containing material.

RF pulsing assisted low-k film deposition with high mechanical strength

Method of forming low-k films with reduced dielectric constant, reduced CHx content, and increased hardness are described. A siloxane film is on a substrate surface using a siloxane precursor comprising O—Si—O bonds and cured using ultraviolet light.

Single precursor low-k film deposition and UV cure for advanced technology node

Methods and apparatus for forming a conformal SiCON film on a surface are described. A SiCN film is formed on a substrate surface and exposed to a low temperature steam annealing process to form a film resistant to damage by rapid thermal processing or ashing. The film is treated by rapid thermal processing and then subjected to a high temperature anneal to form a film with a low dielectric constant.

Methods and apparatus for deposition of low-k films

Exemplary methods of forming a silicon-and-carbon-containing material may include flowing a silicon-oxygen-and-carbon-containing precursor into a processing region of a semiconductor processing chamber. A substrate may be housed within the processing region of the semiconductor processing chamber. The methods may include forming a plasma within the processing region of the silicon-and-carbon-containing precursor. The plasma may be formed at a frequency less than 15 MHz (e.g., 13.56 MHz). The methods may include depositing a silicon-and-carbon-containing material on the substrate. The silicon-and-carbon-containing material as-deposited may be characterized by a dielectric constant below or about 3.5 and a hardness greater than about 3 Gpa.

Systems and methods for depositing low-k dielectric films

A method for dielectric filling of a feature on a substrate yields a seamless dielectric fill with high-k for narrow features. In some embodiments, the method may include depositing a metal material into the feature to fill the feature from a bottom of the feature wherein the feature has an opening ranging from less than 20 nm to approximately 150 nm at an upper surface of the substrate and wherein depositing the metal material is performed using a high ionization physical vapor deposition (PVD) process to form a seamless metal gap fill and treating the seamless metal gap fill by oxidizing/nitridizing the metal material of the seamless metal gap fill with an oxidation/nitridation process to form dielectric material wherein the seamless metal gap fill is converted into a seamless dielectric gap fill with high-k dielectric material.

Methods for seamless gap filling of dielectric material

Exemplary semiconductor processing methods may include flowing deposition gases that may include a nitrogen-containing precursor, a silicon-containing precursor, and a carrier gas, into a substrate processing region of a substrate processing chamber. The flow rate ratio of the nitrogen-containing precursor to the silicon-containing precursor may be greater than or about 1:1. The methods may further include generating a deposition plasma from the deposition gases to form a silicon-and-nitrogen containing layer on a substrate in the substrate processing chamber. The silicon-and-nitrogen-containing layer may be treated with a treatment plasma, where the treatment plasma is formed from the carrier gas without the silicon-containing precursor. The flow rate of the carrier gas in the treatment plasma may be greater than a flow rate of the carrier gas in the deposition plasma.

Tensile nitride deposition systems and methods

Semiconductor processing methods are described for forming UV-treated, low-&#x3ba; dielectric films. The methods may include flowing deposition precursors into a substrate processing region of a semiconductor processing chamber. The deposition precursors may include a silicon-and-carbon-containing precursor. The methods may further include generating a deposition plasma from the deposition precursors within the substrate processing region, and depositing a silicon-and-carbon-containing material on the substrate from plasma effluents of the deposition plasma. The as-deposited silicon-and-carbon-containing material may be characterized by greater than or about 5% hydrocarbon groups. The methods may still further include exposing the deposited silicon-and-carbon-containing material to ultraviolet light. The exposed silicon-and-carbon-containing material may be characterized by less than or about 2% hydrocarbon groups.

Systems and methods for forming UV-cured low-&#x3ba; dielectric films

Embodiments of the semiconductor processing methods to form low-&#x3ba; films on semiconductor substrates are described. The processing methods may include flowing deposition precursors into a substrate processing region of a semiconductor processing chamber. The deposition precursors may include a silicon-containing precursor that has at least one vinyl group. The methods may further include generating a deposition plasma in the substrate processing region from the deposition precursors. A silicon-and-carbon-containing material, characterized by a dielectric constant (&#x3ba; value) less than or about 3.0, may be deposited on the substrate from plasma effluents of the deposition plasma.

Systems and methods for depositing low-&#x3ba;dielectric films

Exemplary semiconductor processing methods to clean a substrate processing chamber are described. The methods may include depositing a dielectric film on a first substrate in a substrate processing chamber, where the dielectric film may include a silicon-carbon-oxide. The first substrate having the dielectric film may be removed from the substrate processing chamber, and the dielectric film may be deposited on at least one more substrate in the substrate processing chamber. The at least one more substrate may be removed from the substrate processing chamber after the dielectric film is deposited on the substrate. Etch plasma effluents may flow into the substrate processing chamber after the removal of a last substrate having the dielectric film. The etch plasma effluents may include greater than or about 500 sccm of NFplasma effluents, and greater than or about 1000 sccm of Oplasma effluents.

Systems and methods for cleaning low-k deposition chambers

The present invention generally provides a method for forming a dielectric barrier with lowered dielectric constant, improved etching resistivity and good barrier property. One embodiment provides a method for processing a semiconductor substrate comprising flowing a precursor to a processing chamber, wherein the precursor comprises silicon-carbon bonds and carbon-carbon bonds, and generating a low density plasma of the precursor in the processing chamber to form a dielectric barrier film having carbon-carbon bonds on the semiconductor substrate, wherein the at least a portion of carbon-carbon bonds in the precursor is preserved in the low density plasma and incorporated in the dielectric barrier film.

Methods to obtain low k dielectric barrier with superior etch resistivity

Methods are provided for processing a substrate comprising a bilayer barrier film thereon. In one aspect, a method comprises depositing a first barrier layer, depositing a second barrier layer on the first barrier layer, depositing a dielectric layer on the bilayer barrier film formed by the first barrier layer and the second barrier layer, and ultraviolet curing the dielectric layer. In another aspect, a method comprises depositing a first barrier layer, depositing a second barrier layer on the first barrier layer, depositing a dielectric layer on the bilayer barrier film formed by the first barrier layer and the second barrier layer, and curing the dielectric layer with an electron beam treatment.

Growing community of inventors

San Jose, CA, United States of America

Yijun Liu