Hong Kong Applied Science and Technology Research Institute Company, Limited

Yat To (William) Wong

Kwai Chi Chan

Kam Chuen Wan

Ho Ming (Karen) Wan

Kwok Kuen (David) Kwong

Andrea Baschirotto

Tin Ho (Andy) Wu

Hok Mo Yau

Xiao Fei Kuang

An analog-to-digital converter (ADC) has a chopper-stabilized sigma-delta modulator (SDM). The SDM uses switched-capacitor integrators to sample, hold, and integrate an analog input in response to non-overlapping multi-phase clocks. Chopper multipliers are inserted on the inputs and outputs of an op amp in a first stage integrator. The chopper multipliers swap or pass through differential inputs in response to non-overlapping chopper clocks. A master clock operating at a frequency of the multi-phase clocks is divided down to trigger generation of the chopper clocks. Delay lines ensure that the edges of the chopper clocks occur before the edges of the multi-phase clocks. The chopper multipliers have already switched and are thus stable when multi-phase clocks change so charge injection at switches controlled by the multi-phase clocks is not immediately modulated by chopper multipliers. This clock timing increases the time available to respond to charge injection at switches improving linearity.

Reduced residual offset sigma delta analog-to-digital converter (ADC) with chopper timing at end of integrating phase before trailing edge

A cascaded sigma-delta modulator has several modulator loops that have one or two sets of integrators, summers, and scalers, and a quantizer that generates a loop output. Input muxes to each loop select either an overall input or the loop output from a prior loop, allowing the modulator loops to be cascaded in series or to operate separately. Filter-configuring muxes after each modulator loop select either that loop's output or a loop output from any prior loop, or a zero. Each filter-configuring mux drives an input to a modified CIC filter. The modified CIC filter has an initial delay stage that receives the first filter-configuring mux output, and successive integrator stages that each receives a successive filter-configuring mux output. The modified CIC filter is a combination of a digital transform filter and a Cascaded-Integrator-Comb (CIC) filter. Modulator loops are powered down for lower-performance configurations or cascaded together for higher-performance configurations.

Configurable cascading sigma delta analog-to digital converter (ADC) for adjusting power and performance

A Successive-Approximation Register Analog-to-Digital Converter (SAR-ADC) predicts compensation values for use in a future cycle. A compensation value is applied to capacitors in a calibration Y-side capacitor array to compensate for capacitance errors in a binary-weighted X-side capacitor array. Two compute engines pre-calculate predicted-0 and predicted-1 compensation values for a next bit to be converted. At the end of the current cycle when the comparator determines the current bit, the comparator also controls a mux to select one of the two predicted compensation values. Thus the compensation value is available at the beginning of the next bit's cycle, eliminating a long calculation delay. The compensation value for the first bit to be converted, such as the MSB, is calculated during calibration. Compensation values for other bits are data-dependent. Calibration values are accumulated during calibration to generate the first conversion compensation value for the first bit to be converted.

Parallel pipelined calculation of two calibration values during the prior conversion cycle in a successive-approximation-register analog-to-digital converter (SAR-ADC)

A calibrating Analog-to-Digital Converter (ADC) has an X-side array with binary-weighted capacitors that connect to an X-side line and a Y-side array connected to a Y-side line. Each array has binary-weighted capacitors from a most-significant-bit (MSB) to a least-significant-bit (LSB), but the LSB capacitor is duplicated as a termination capacitor and a middle capacitor between upper and lower groups is also duplicated as a surrogate capacitor. During calibration, lower array capacitors are switched low while the upper capacitors are driven by a thermometer-code value on both X and Y arrays. The thermometer value is inverted to the X-array but remains uninverted on the Y array. The lower array bits are tested to final a calibration value that has X and Y side voltages balanced.

Charge compensation calibration for high resolution data converter

A pre-amplifier circuit can be cascaded and drive a latch for use in a precision analog-to-digital converter (ADC). The pre-amplifier has a main section and a feedback section connected by feedback resistors that do not produce voltage drops in the main section. Offset is stored on offset capacitors during an autozeroing phase and isolated by transmission gates during an amplifying phase. The offset capacitors drive the gates of feedback transistors that drive output nodes in the main section. Autozeroing sink transistors in the feedback section operate in the linear region while current sink transistors in the main section operate in the saturated region. Kickback-charge isolation transistors may be added for charge isolation. The output may also be equalized by an equalizing transmission gate. A very low power-supply voltage is supported even for high-speed operation with offset cancellation, due to the folded feedback resistor arrangement.

Ultra low voltage multi-stage high-speed CMOS comparator with autozeroing

A bandgap reference circuit has trimming-up resistors and trimming-down resistors for bi-directional trimming. PNP transistors have base and collectors grounded and emitters connected to parallel resistors. A difference resistor drives an inverting input of an op amp that drives a transistor that generates the bandgap reference voltage Vbg. A sensing resistor connects Vbg to a splitting node that connects to the non-inverting input through a first parallel resistor. The splitting node also connects through a second parallel resistor to the inverting input. Fuses or switches enable the trimming-up and trimming-down resistors. The trimming-up resistors are in series with the sensing resistor and the trimming-down resistors are in series with an output resistor that connects Vbg to reference voltage Vref. The circuit can be designed for a more typical process since bi-directional trimming allows Vref to be raised or lowered. Many circuits need no trimming when targeted for the typical process.

Growing community of inventors

Hong Kong, China

Yat To (William) Wong