Daikin Industries, Ltd.

Hiroshima University

Yasuyuki Yamaguchi

Tadaharu Isaka

Hiroyuki Hamada

Hayato Tsuda

Yumi Zenke

Yukari Yamamoto

Masamichi Sukegawa

Manabu Fujisawa

Hideki Kono

Yuuki Kuwajima

Toshiyuki Fukushima

Hitoshi Imamura

Kenji Ishii

Ken Okanishi

Masamichi Hikosaka

Kiyoka Okada

Kyouhei Sawaki

Kiyofumi Nakamura

Mitsugu Omori

Takeshi Kozuki

Hiroaki Wada

Provided is a pipe joint including a cylindrical hollow, wherein the wall thickness of a part having the largest wall thickness of the pipe joint is 2 to 7 mm, the ratio of the length of the hollow in the axial direction (L) to the diameter of the hollow (D), (L/D), is 5 or less, the pipe joint contains a copolymer containing tetrafluoroethylene unit and a fluoro(alkyl vinyl ether) unit, the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 2.8 to 6.0% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 4.0 g/10 min or higher and lower than 11.0 g/10 min, and the number of functional groups of the copolymer is 50 or less.

Pipe joint and manufacturing method of pipe joint

Provided is an injection molded article containing a copolymer containing tetrafluoroethylene unit and a fluoro(alkyl vinyl ether) unit, wherein the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 3.9 to 4.8% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 11.0 to 19.0 g/10 min, the melting point of the copolymer is 296 to 305° C., and the amount of fluorine ions dissolving out from the injection molded article into water is 7,500 μg/mor lower.

Injection-molded body and production method therefor

Provided an injection molded article obtained by injection molding a copolymer using a mold provided with a gate, wherein the copolymer contains tetrafluoroethylene (TFE) unit and a fluoro(alkyl vinyl ether) (PAVE) unit, the content of the fluoro(alkyl vinyl ether) unit of the copolymer is 3.5 to 4.7% by mass with respect to the whole of the monomer units, the melt flow rate at 372° C. of the copolymer is 22.0 to 35.0 g/10 min, the number of functional groups of the copolymer is 20 or less per 10main-chain carbon atoms, and the injection molded article has a gate section corresponding to the gate of the mold, and the ratio of the maximum flow length from the gate section of the injection molded article (a) to the average value of the product thickness on the maximum flow length (b), ((a)/(b)), is 80 to 200.

A magnet wire including a conductor and an insulating coating formed on an outer periphery of the conductor. The insulating coating contains a copolymer containing a tetrafluoroethylene unit and a fluoroalkyl vinyl ether unit. The copolymer has a melt flow rate of 10 to 60 g/10 min, and the copolymer has a fluoroalkyl vinyl ether unit content of 6.2 to 8.0% by mass based on a total content of monomer units.

Magnet wire and coil

A fluorocopolymer having a tetrafluoroethylene-derived constituent unit as essential unit, and hexafluoropropylene-derived constituent unit and/or perfluoro(alkyl vinyl ether)-derived constituent unit, wherein, when the fluorocopolymer is molded into a film, the film has not more than 10000 fisheyes capable of enclosing a square with a side length of 44 &#x3bc;m and incapable of enclosing a square with a side length of 178 &#x3bc;m per 100 g and not more than 1000 fisheyes capable of enclosing a square with a side length of 178 &#x3bc;m per 100 g.

Fluorinated copolymer, electric wire, and method for production of the electric wire

A non-electrification polymeric composite material composed of a tetrafluoroethylene/fluoro(alkyl vinyl ether) copolymer containing 4% by weight or more fluoro(alkyl vinyl ether) and an electrically conductive material. This non-electrification polymeric composite material is suitably used in a holder for holding a semiconductor substrate, or the like.

Non-electrification polymeric composite material

Growing community of inventors

Settsu, Japan

Yasuyuki Yamaguchi