Citic Dicastal Co., Ltd

Xiaopeng Chen

Zuo Xu

Xiao Liu

Huiying Liu

Yongwang Zhao

Jiandong Guo

Weidong Liu

Hanqi Wu

Haiping Chang

Guangcai Chen

Jun Wang

Dan Yao

Yule Zhou

Shan Ma

Chong Li

Junmeng Li

Lijie Hu

Qun Zhao

Guohua Liu

Le Wang

Lei Bao

Yudong Li

Zenglei He

Xing Wang

Xingming Zhang

A self-centering device for a liner press-fit wheel may improve center alignment when liners are pressed in bolt holes of the wheel, may reduce rejects generated when bolt hole materials are pressed out by alignment failures, and may improve a press-fit yield.

Self-centering device for cylinder liner press-fit wheel

A wheel fixture is disclosed. A main shaft drives a first positioning pull rod on a chuck body to extend and contract in the radial direction via a tightening screw, a clamping jaw is at a position within the travel range of extension and contraction, a wheel is positioned and clamped by the fixture, airtight support blocks are pressed down by the wheel and flush with the support plane of the clamping jaw, at this time, airtight ejector rods press second O rings to prevent air from flowing out of the airtight detection position, a detection system of a machine tool detects a preset air pressure value which indicate that the wheel has been placed correctly, and if the wheel is not placed correctly on the fixture, the machine tool will alarm through the detected pressure feedback.

Wheel fixture

A positioning clamp for spray-coating of a wheel trim ring includes a lower base plate, a circular bracket, an upper base plate, a plurality of guide rods, a plurality of sliding support parts and a distance adjusting mechanism. The distance adjusting mechanism is configured to drive the plurality of sliding support parts to approach a central position along the guide rods and to move away from the central position along the guide rods. According to the positioning clamp for spray-coating of the wheel trim ring, the position of each sliding support part can be adjusted to adapt to wheel trim rings of different sizes. Therefore, the positioning clamp for spray-coating of the wheel trim ring can replace a large number of positioning clamps of different sizes, and has the advantages of being simple in structure, stable and reliable in positioning, low in manufacturing cost and the like.

Positioning clamp for spray-coating of wheel trim ring

A milling fixture for forged wheel includes a connecting plate installed on a milling machine table, a linear bearing installed on the connecting plate, a small diameter end of a positioning rod penetrates through a spring and a linear bearing, and a limiting screw installed on a side wall of the linear bearing and connected with the positioning rod. Under the coaction of the spring and an external force, the positioning rod is configured to move in the linear bearing. Bidirectional threaded rods are uniformly installed on a bottom plate, one end of each of the bidirectional threaded rods penetrate through pressure claws, the pressure claws are sandwiched between compression nuts and the connecting plate. The fixture can meet the requirement for milling a forged wheel, and at the same time, has the characteristics of a simple structure, is convenient to manufacture, provides stable performance and is low cost.

Milling fixture for forged wheel

A wheel corner polishing device includes a station switching system, a valve hole polishing system, a bolt hole polishing system and a rim and cap section synchronous polishing system. The wheel corner polishing device can automatically polish four positions including bolt hole corners, a valve hole corner, outer rim corners and cap section corners of a wheel via upper and lower stations and coordination of the systems.

Wheel corner polishing device

A wheel outer rim fillet dressing device, wherein after a wheel is roughly positioned, an electric cylinder drives a moving plate to descend to an appropriate position, an adjusting cylinder drives a second sliding table to move away from a first sliding table, the first sliding table moves synchronously with the second sliding table under the action of a second gear rack, thus the distance between a precision positioning post on the first sliding table and a precision positioning post on the second sliding table is adjusted, and the precision positioning posts contact a vertical surface of a cap seam allowance of the wheel and hold the wheel tightly. The adjusting cylinder is restarted, and the outer rim fillets can be dressed when the distance between first and second cutters for dressing wheel outer rim fillets is adjusted to an appropriate position and under the cooperation of the rotating wheel.

Wheel outer rim fillet dressing device

Disclosed is an aluminum alloy hub surface treatment process. The specific process flow comprises: providing an aluminum alloy hub blank, sanding, polishing, pre-treating, spraying electroplating silver paint, flash-drying, spraying celluloid paint, curing and discharging. The process not only has the mirror effect of electroplated products, but also has many advantages of simplicity, low cost, no heavy metal pollution and the like.

Aluminum alloy hub surface treatment process

Growing community of inventors

Qinhuangdao, China

Xiaopeng Chen