Fasco Industries, Inc.

Fasco Controls Corporation

Willis E Rieman

Leon G Barry

The dipstick has an enlarged head and an integral, flexible shank which extends slidably through the dipstick tube of a conventional engine crankcase so that a pair of spaced thermistors, which are mounted on the shank adjacent its inner end, normally will be immersed beneath the level of the oil in the crankcase. The shank contains a ground conductor which is connected adjacent one end to one side of the thermistors, and adjacent its opposite end has sliding, resilient engagement with the inside of the dipstick tube. The opposite sides of the thermistors are connected by two additional conductors which extend upwardly in the shank to register with a pair of openings that are formed in diametrally sides of the shank near the dipstick head. A clamp, which is secured to the outer end of the dipstick tube, carries a pair of spaced terminals, the inner ends of which project through the opposed openings in the dipstick and slidably and resiliently into engagement with the upper ends of the two conductors, when the dipstick is seated in the dipstick tube. The opposite ends of these two terminals are releasably connected to an indicator circuit which produces an alarm signal when the temperature differential detected by the two thermistors exceeds a predetermined value.

Engine oil level sensor

Two wire leads project from opposite ends of a dielectric housing having a sealed chamber containing a fusible metal alloy link, which operatively connects the wire leads electrically to one another. A flexible, pre-loaded, dielectric spring element in the chamber engages and exerts upon the link a predetermined stress, which is operative to cause the link suddenly to fail and interrupt the connection between the leads, when the ambient temperature of the link exceeds a predetermined temperature range. In one embodiment the two wire leads project into the chamber and have spaced, confronting ends interconnected by the link, one side of which is held under compressive stress by the spring element. In a second embodiment a sinuous spring element is formed on one end of one lead, and extends into the chamber where its free end is soldered under tension to one wall of the chamber in electrical contact with the second lead wire, so that when the link melts the tensioned spring element is disconnected from the second lead wire.

Non-resettable thermal fuse

This two-piece fuse comprises a generally rectangular plastic, dielectric housing, and a one-piece wire conductor. The conductor is folded into generally W-shaped configuration, and its inverted, V-shaped center section is inserted into a central recess in the bottom of the housing in such manner that its two, spaced, V-shaped legs are bent around the grooved, rounded ends of a pair of rigid web sections which project from the underside of the housing. Opposite ends of the folded wire are secured in a pair of spaced openings in the housing so that the two V-shaped legs of the wire are supported in a common plane by two web sections of the housing. The diameter of the wire is greater than the depth of the groove in each web section so that portions of the wire legs project out of the grooves for engagement with contacts when the leg sections of the wire are inserted into a cooperating female receptacle.

Plug-in type fuse

A one-piece wire lead has intermediate its ends a thin, flattened section which is seated against a recessed die surface that is formed on one end wall of a hermetically sealed chamber in a preferably transparent, paraboloidally-shaped plastic housing. The two cylindrical leg sections of the lead project out of the opposite end of the chamber for connection in series with a conductor in a circuit that is to be protected. A plastic, electrically non-conductive, spring-loaded sabot is mounted to reciprocate in the chamber between a retracted position in which a sharp cutting edge on the forward end thereof faces one side of the flattened section of the lead, and an advanced position in which the sabot cutting edge has cut through the flattened lead section, and has extended into a recess in the die surface. Normally a compacted, granular thermal plug is cast or molded around either the sharp cutting edge of the sabot, or its operating spring, thereby normally to retain the sabot in its retracted position. When the ambient temperature of the fuse exceeds a predetermined value the plug melts suddenly and permits its spring to drive the sabot cutting edge suddenly through the flattened section of the wire lead completely to sever the lead intermediate its ends.

Growing community of inventors

Shelby, NC, United States of America

Willis E Rieman