Hottinger Baldwin Messtechnik Gmbh

Werner Schlachter

Ralf Waegner

Hans-Joachim Gerlach

Ralf Scherer

Heinz Ronald Will

Heinz-Ronald Will

Andreas Jaeger

Ronald Will

Hans-J Gerlach

Markus Franz

Ursula Host

Stefan Schmidt

Andreas Jäger

A force transducer for measuring compression and/or tension forces includes a rod-shaped deformation body and at least four strain transducers applied on the deformation body and configured for measuring a longitudinal strain and a transverse strain of the deformation body. Front and rear elongate recesses are provided on the front and rear sides of the deformation body at an intersection point between a central longitudinal axis and a central transverse axis of the deformation body. Left and right upper indentations and left and right lower indentations are provided on the deformation body respectively at the four quadrants bounded by the axes. An angle between the central transverse axis and a shortest connecting line between the front elongate recess and the left upper indentation is at least 17&#xb0; and at most 29&#xb0;.

Rod-shaped force transducer with simplified adjustment

A force transducer for measuring compression and/or tension forces includes a rod-shaped deformation body and at least four strain transducers applied on the deformation body and configured for measuring longitudinal and transverse strains thereof. Front and rear elongate recesses are provided on the front and rear sides of the deformation body in the area of an intersection between a central longitudinal axis and a central transverse axis of the deformation body. Left and right upper indentations and left and right lower indentations are provided on the deformation body respectively at the four quadrants bounded by the axes. A ratio of a cross-section on a center plane extending orthogonally to the central longitudinal axis and including the central transverse axis, to a sum of first and second partial regions of the cross-section, is from 1.56 to 2.15.

Rod-shaped force transducer with improved deformation behavior

A measuring pick-up or load cell shall be made less sensitive against off-center load applications, if necessary. At least it must be made certain that the off-center load sensitivity is within a permissible tolerance range. For this purpose the sensor body (1A, 1', SB) of the detector (1) to which there is applied at least one pick-up element or strain gage (5), is held for each load application in a different fixed position in a mounting (2) in such a way that, spaced from the clamping position a test load can be applied in a direction deviating from the direction and/or position of the axis of symmetry (CA, AS) of the sensor body (1A, 1', SB). The test loads may be uniform or they may differ for one or more load application points. A respective output signal is measured and correlated to the applied test load. At least one additional test load of the same size is applied in a different load application direction, and the respective output signal is again measured and correlated to the second test load. Then, the output signals are evaluated with reference to a tolerance range (TR) stored in a memory of a control unit (11) to determine whether a tuning of the sensor body is necessary to make the pick-up less sensitive. If such tuning is necessary, at least one tuning is performed. The tuning may be a mechanical material removal from the sensor body and/or as an electrical tuning by resistor adjustments.

Method and apparatus for making load cells less sensitive to off-center

A measuring pick-up or detector shall be made less sensitive against off-center load applications if necessary. At least it must be made certain that the off-center load sensitivity is within a permissible tolerance range. For this purpose the sensor body (1A, 1', SB) of the detector (1) to which there is applied at least one pick-up element or strain gage (5), is held for each load application in a different fixed position in a mounting (2) in such a way that, spaced from the clamping position a test load can be applied in a direction deviating from the direction and/or position of the axis of symmetry (CA, AS) of the sensor body (1A, 1', SB). A respective output signal is measured and correlated to the applied test load. At least one additional test load of the same size is applied in a different load application direction, and the respective output signal is again measured and correlated to the second test load. Then, the output signals are evaluated with reference to a tolerance range (TR) stored in a memory of a control unit (11) to determine whether a tuning of the sensor body is necessary to make the pick-up less sensitive. If such tuning is necessary, at least one tuning is performed. The tuning may be a mechanical material removal from the sensor body and/or as an electrical tuning by resistor adjustments.

Method and apparatus for making load measuring pick-ups less sensitive

The rotation of a rocker pin about the longitudinal pin axis in a rocker pin load cell is limited by a collar (7) directly connected to a pin end and having spaced stop surfaces (11, 12; 11', 12') cooperating with a stop stud (8) mounted in a socket (4 or 3) in which the pin end with its collar (7) is held. The long axis of the stop stud extends in parallel to the pin axis in its normal vertically aligned position.

Growing community of inventors

Darmstadt, Germany

Werner Schlachter