Chartered Semiconductor Manufacturing Ltd (corporation)

Other

Vijai Kumar Chhagan

Yelehanka Ramachandramurthy Pradeep

Henry Gerung

Mei Sheng Zhou

Simon Yew-Meng Chooi

Subhash Gupta

Igor V Peidous

Jian Xun Li

Chivukula Subrahmanyam

Madhusudan Mukhopadhyay

Konstantin V Loiko

Yelehanka Ramachandramurthy

Tan Poh Suan

Quek Kiok Elgin

A method for making low sheet resistance local metal interconnections and improved transistor performance is described. The method involves patterning a polysilicon layer and a silicon nitride (Si N ) cap layer over device areas to form FET gate electrodes, and the patterned polysilicon extends over the field oxide regions to form portions of the local interconnections. After forming source/drain areas and sidewall spacers on the FET gate electrodes, a silicon oxide (SiO ) insulating layer is deposited and polished back to the Si N cap. The Si N is then selectively removed over the patterned polysilicon layer, leaving recesses in the SiO layer. After etching contact openings in the SiO layer to the substrate, a high electrically conducting metal layer, having a barrier layer, is deposited and patterned to complete the local interconnections. Portions of the metal are retained in the recesses over the pattered polysilicon layer to improve transistor performance, while portions of the metal in the contact openings provide low-contact resistance to the substrate.

Method for fabricating local metal interconnections with low contact resistance and gate electrodes with improved electrical conductivity

A new method of forming silicon nitride sidewall spacers has been achieved. In addition, a new device profile for a silicon nitride sidewall spacer has been achieved. An isolation region is provided overlying a semiconductor substrate. Polysilicon traces are provided. A liner oxide layer is formed overlying the polysilicon traces and the insulator layer. A silicon nitride layer is formed overlying the liner oxide layer. A polysilicon or amorphous silicon layer is deposited overlying the silicon nitride layer. The polysilicon or amorphous silicon layer is completely oxidized to form a temporary silicon dioxide layer. The temporary silicon dioxide layer is rounded in the corners due to volume expansion during the oxidation step. The temporary silicon dioxide layer is anisotropically etched through to expose horizontal surfaces of the silicon nitride layer while leaving vertical sidewalls of the temporary silicon dioxide layer. The silicon nitride layer is anisotropically etched to form silicon nitride sidewall spacers with an L-shaped profile. The integrated circuit device is completed.

Method to form self-aligned, L-shaped sidewall spacers

A method for forming an extended metal gate without poly wrap around effects. A semiconductor structure is provided having a gate structure thereon. The gate structure comprising a gate dielectric layer, a gate silicon layer, a doped silicon oxide layer, and a disposable gate layer stacked sequentially. Spacers are formed on the sidewalls of the gate structure. A dielectric gapfill layer is formed over the semiconductor structure and the gate structure and planarized, stopping on the disposable gate layer. A first silicon nitride layer is formed over the disposable gate layer, and a dielectric layer is formed over the first silicon nitride layer. The dielectric layer is patterned to form a trench over the gate structure; therein the trench has a width greater than the width of the gate structure. The first silicon nitride layer in the bottom of the trench and the disposable gate layer are removed using one or more selective etching processes. The doped silicon oxide layer is removed using an etch with a high selectivity of doped silicon oxide to undoped silicon oxide. A barrier layer is formed over the gate silicon layer, and a metal gate layer is formed on the barrier layer; whereby the metal gate layer has a greater width than the gate structure.

Method for forming an extended metal gate using a damascene process

A new method is provided for the integration of the of T-top gate process. Active regions are defined and bounded by STI's on the surface of a substrate. The pad oxide is removed from the substrate and replaced by a layer of SAC oxide. A thin layer of nitride is deposited that covers the surface of the created layer of SAC oxide and the surface of the STI regions. A layer of TEOS is deposited and etched defining the regions where the gate electrodes need to be formed. Gate spacers are next formed on the sidewalls of the openings that have been created in the layer of TEOS. The required implants (such as channel implant and threshold implant) are performed, the gate structure is then grown in the openings that have been created in the layer of TEOS. After the gate structure has been completed, the surface of the created structure is polished and the remaining layer of TEOS is removed. Source and drain regions implants can now be performed, LDD regions are implanted using a tilted implant. This tilted implant penetrates underneath the body of the created gate structures thereby creating the LDD regions. The removal of the layer of TEOS leaves in place the gate structures, one such structure is located in the active region of the surface of the substrate, two additional structures that have been created on the surface of the STI regions.

Self aligned T-top gate process integration

A new method of forming metal interconnects with air gaps between adjacent interconnects in the manufacture of an integrated circuit device is achieved. A semiconductor substrate is provided. The metal interconnects are formed overlying the semiconductor substrate. A silicon nitride liner layer is deposited. A gap filling oxide layer is deposited to fill gaps between adjacent metal interconnects. The gap filling oxide layer is polished down to the silicon nitride liner layer. A silicon nitride thin layer is deposited. The silicon nitride thin layer is patterned using an oversized, reverse mask of the metal interconnects. The patterning of the silicon nitride thin layer creates openings to thereby expose a portion of the gap filling oxide. The gap filling oxide layer is etched away. A self-sealing oxide layer is deposited overlying the silicon nitride thin layer and the silicon nitride liner layer. The self-sealing oxide layer seals over the gaps between the silicon nitride thin layer and the silicon nitride liner layer to thereby form permanent air gaps between the adjacent metal interconnects, and the integrated circuit is completed.

Method to form self-sealing air gaps between metal interconnects

A novel design of an oxidation mask for improved control of birds beak and more specifically for tailoring and smoothing the field oxide isolation profile in the vicinity of the birds beak. The mask design is particularly advantageous for narrow field isolation spacings found in sub half-micron integrated circuit technology. The mask uses a thin tapered silicon nitride foot along its lower edge to allow nominal expansion of the oxide during the early stages of oxidation, thereby permitting in-situ stress relief as well as a smoothing of the oxide profile. The taper of the foot provides a gradual increase in mask stiffness as oxidation proceeds under the mask edge, allowing greatest flexibility during the early rapid growth period followed by increasing stiffness during the later stages when the growth rate has slowed, thereby inhibiting the penetration of birds beak. Shear stresses responsible for dislocation generation are reduced by as much as fifty fold. This stress reduction is accompanied by an improvement in surface topography as well as suppression of oxide punchthough and the narrow oxide thinning effect.

Growing community of inventors

Belgrave, United Kingdom

Vijai Kumar Chhagan