Itron Gmbh

Itron Global Sarl

Other

Viet-Hung Nguyen

Jerome Bartier

Bastien Mainaud

Hartman Van Wyk

James Laurence Taylor

Fabrice Monier

Daniel Popa

Mehdi Mani

Yacine Khaled

Michael T Garrison Stuber

Keith W Barnes

Jorjeta Gueorguieva Jetcheva

John Buffington

Kenneth Charles Rigdon

Ahmad Kaouk

Elliott Adam Nelson

Iskander Banaouas

Vincent Roussel

Iman Mayassa Zendjebil

Hussein Kdouh

Bruno Andrianasolo

Techniques configure a network to relay data from a node to a root device are described herein. In an example, one-hop neighbors of the node are determined and ranked according to link quality. The ranked neighbor nodes may be considered potential 'parent nodes' of the node. The ranked nodes may be divided into a plurality of groups according to link quality. A parent node may be selected from among the 'best' group of one-hop neighbor nodes and may be used to relay data for the node to and/or from the router or other device. The node continues to use the parent node at least until its ranking removes it from the best group or falls below a threshold value. After the ranking of the parent falls below such a prescribed threshold it may be replaced by selection of a replacement parent from the group of one-hop upstream neighbors having the best link quality.

Rank and routing techniques for networked device

Source routing techniques include sending data across several networks, while limiting source routing overhead. For example, the source routing techniques may use a first address format to route data to nodes along a routing path that are within a first network where a source node is located, and use a second address format to route the data to a node along the routing path that is within a second, different network. The node in the second network may similarly route the data through the second network using the first address format for nodes within the second network and, if needed, route the data to a node within a third network using the second address format. This may be repeated for any number of networks to reach a destination.

Partial source routing for cross-network routing

Techniques for bridging communication between multiple networks to facilitate distribution of multicast data are described herein. For example, a node that is able to communicate with its network and an adjacent network may send a subscription message indicating that the node is a member of a multicast group. The subscription message may be forwarded up both networks. The node may then forward, between the networks, data that is destined for members of the multicast group.

Multi-network operation with member node for multicast groups

Techniques for connecting networks to facilitate distribution of data are described. For example, to distribute multicast data to members of a multicast group that span multiple networks, the techniques may identify a path between networks that each have a member of the multicast group, such as a shortest path between networks. The techniques may inform the networks on the path to establish a connection with an adjacent network. This may allow multicast data for a multicast group to be distributed to members of the multicast group that are located in separate networks.

Connecting multiple networks for multicast groups

Techniques are directed to opportunistically communicating using a modulation scheme that is other than the preferred modulation scheme, to update communication metric data for the second modulation scheme, such as a modulation scheme that has not been used as much as the first modulation scheme. The second modulation scheme may be associated with a higher data rate than the preferred modulation scheme. If communication using the second modulation scheme is successful, subsequent communication may be carried out exclusively using the second modulation scheme, and the communication metrics may develop such that the second modulation scheme becomes the preferred modulation scheme.

Opportunistic use of different modulation schemes

Techniques for controlling packet transmission levels in a multi-hop network may be performed in a distributed manner. Load-control functionality may be distributed among a plurality of nodes within a network, allowing such nodes to send feedback to upstream nodes, and receive feedback from downstream nodes. In an example, received packets are measured, such as by summing sizes of received packets over time, to determine a received traffic-level. Transmitted packets are measured, such as by summing sizes of transmitted packets over time, to determine a transmitted traffic-level. Feedback may be sent to at least one source of the received packets based at least in part on the received traffic-level and the transmitted traffic-level. The feedback may indicate a desired rate for the sender to transmit. A node may receive data from upstream node(s) and from an internal device, such as a metrology unit. Both data sources may be controlled by feedback.

Distributed load-control in multi-hop networks

A new device is deployed to an area in which a network is provided. The new device may join the network using a single handshake via a neighboring device that is a member of the network and register with a network management system managing the network. If the network is overloaded or has limited bandwidth remaining, the network may refuse to admit the new device, or if the new device is isolated, may force some devices that are members of the network to leave or migrate from the network to allow the isolated device to join the network.

Efficient device handover/migration in mesh networks

Techniques for limiting forwarding of multicast communications are described herein. For example, the techniques intelligently forward data along paths of a network where members of a multicast group are located. As such, nodes that do not lead to members of the multicast group may be pruned from distribution of the data. This reduces network communications, ultimately conserving processing, communication, and/or battery resources of the nodes.

Limiting forwarding of multicast communications

Techniques for bridging communication between multiple networks to facilitate distribution of multicast data are described herein. For example, the techniques may identify a particular node that is able to communicate with each network and instruct the particular node to act as a bridge between the networks. The particular node may forward data from either network to the other network. This may allow data for a multicast group to be distributed to members of the multicast group that are located in separate networks.

Multi-network operation for multicast groups

Techniques for broadcasting data in a multi-channel network having a control channel and multiple data channels are described. A node wishing to broadcast data may determine a particular data channel from among the multiple data channels, a modulation technique, and a data rate to be utilized to broadcast the data. The broadcasting node may transmit a message over the control channel indicating that the data will be broadcast on the particular data channel using the modulation technique and at the determined data rate. The broadcasting node and a node wishing to receive the data may switch to the particular data channel. The broadcasting node may broadcast the data over the particular data channel, while the receiving node may receive the data. After broadcasting the data or a predetermined time period has expired, the broadcasting node and receiving node may switch to the control channel.

Data broadcasting with a prepare-to-broadcast message

Techniques directed to attributing information regarding communications with a modulation scheme to a different modulation scheme are described. In one example, a successful communication for a higher data rate modulation scheme may be attributed to a lower data rate modulation scheme. Such attribution may infer that the lower data rate modulation scheme would have also been successful if it had been used. In another example, an unsuccessful communication for a lower data rate modulation may be attributed to a higher data rate modulation scheme. Here, such attribution may infer that the higher data rate modulation scheme would have also been unsuccessful if it had been used.

Coherent link quality across multiple modulations

A node having a multiple protocol receiver may listen to multiple links in parallel and determine a quality of links having multiple communication technologies between the node and multiple neighbor nodes. The multiple communication technologies may include radio frequency (RF) communication technologies and one or more power line communication (PLC) communication technologies. The node determines a link quality metric for each link associated with an optimum communication technology and data rate, and maintains availability information of neighbor nodes. The node may then route communications to neighbor nodes using the link quality metric and the availability information.

Growing community of inventors

Saint Mande, France

Viet-Hung Nguyen