Case Corporation

Cnh America LLC

Cnh Industrial America LLC

Troy D Bateman

Anthony John Lamela

Brian E Felsing

Peter John Dix

Hong-Chin Lin

Daniel B Shore

Jürgen Weber

Michael Sylvester Bares

Yun Xing

Jarrod A Lemire

Regis Bellanger

John R Harms

A method for reducing fuel consumption of a work vehicle may include monitoring one or more loads associated with both a drive power requirement and a hydraulic power requirement for the work vehicle. In addition, the method may include actively adjusting one or more operating parameters of the work vehicle based on the monitored loads in a manner that meets the drive power requirement and the hydraulic power requirement for the work vehicle while reducing the fuel consumption of the vehicle's engine.

System and method for reducing fuel consumption of a work vehicle

A work vehicle includes a frame and an axle assembly coupled to the frame, including a first axle shaft substantially disposed in an axle housing. A first wheel couples to the first axle shaft of the axle assembly. An axle lubricating fluid is disposed within the axle housing. A cooling circuit fluidly coupled to the axle assembly circulates cooling fluid therethrough. A hydraulic motor fluidly coupled to a fluid circuit includes a device disposed in parallel with the fluid circuit to discontinue operation of the motor in response to a predetermined pressure of at least one of the first and second circuit being exceeded.

External axle cooling system

A skid steer vehicle has a chassis with four drive wheels suspended from the chassis that are damped by four damping cylinders. An electronic controller varies the damping of the cylinders in an automatic mode, based on certain operational parameters of the vehicle, and in a manual mode in response to operator selection of a desired degree of suspension damping.

Variable ride control

A skid steer vehicle has two drive motors that are connected by belts to spring-mounted front and rear wheels.

Skid steer vehicle with belt drive suspension

A skid steer vehicle is supported on four gearboxes that function both as control arms and as speed reduction gearboxes. Each side of the vehicle's chassis has two gearboxes to which it is coupled. A hydraulic motor is fixed to each side of the chassis to drive the gearboxes on that side. The motors are arranged such that their drive shafts extend longitudinally along the chassis, with a front shaft engaging the front gearbox and a rear shaft engaging the rear gearbox. The gearboxes include three speed-reducing right angle gear sets coupling an axle extending from the gearbox to the motor driving that gearbox.

Direct drive suspension

A skid steer vehicle has a suspension that includes two bogies pivotally connected to the sides of the vehicle and extending fore-and-aft along each side of the vehicle. The bogies are pivotally connected to the vehicle in the middle and have a wheel mounted at each end. A hydraulic motor is coupled to each of the bogies and drives the two wheels on each bogie.

Skid steer vehicle with bogie suspension

A skid steer vehicle has a drive system that includes a hydraulic motor coupled to a speed-reduction gearbox. One or more drive shafts extend fore-and-aft from the gearbox and are coupled at each end to two axle housings. Each axle housing includes two reduction gear sets and an axle. Each of the axles extends outward from the vehicle and a wheel is fixed to its outer end. A spur gear on a parallel shaft inside the axle housing engages a spur gear on the axle and drives it to provide one gear reduction. A bevel gear in the axle housing engages a bevel gear on the parallel shaft to provide another gear reduction. The vehicle has a drive system located on each side of the vehicle to collectively drive four wheels.

Skid steer vehicle with axle housing having a double gear reduction

A skid steer vehicle has a drive system that includes hydraulic motor coupled to a reduction gearbox. A driveshaft extends fore-and-aft from the gearbox and is coupled at each end to a combined housing including a reduction gear set and an axle. The axle extends laterally outward from the vehicle and a wheel is fixed to its outer end. There are two housings on either end of the driveshaft. There are two such drive systems on the vehicle, one on either side. Thus the vehicle has two separate drive systems, each capable of independently driving two wheels on opposing sides of the vehicle.

Skid steer vehicle with direct drive

A control system for a skid steer vehicle reads a load height sensor, a load amount sensor, and a vehicle speed sensor to derate the otherwise commanded acceleration, deceleration and turning rate on the vehicle when the vehicle has too great a load, too high a load, or the vehicle is going too fast.

Skid steer drive control system

A skid steer vehicle with steerable suspension has hydraulic motors coupled to four steerable wheels. The wheels are turned by hydraulic actuators and the vehicle is steered either by turning the wheels or by driving the wheels on opposite sides of the vehicle in opposite directions and skid steering the vehicle.

Skid steer vehicle with steerable suspension

A skid steer vehicle has sprung suspensions, variable displacement pumps and motors connected to those pumps that drive the wheels on the vehicle as well as an electronic controller that receives signals that indicate fore-and-aft acceleration of the skid steer vehicle. Based on these signals, the controller determines whether the forward acceleration exceeds a predetermined value and locks up the rear suspensions if that value is exceeded. It also determines whether the forward deceleration exceeds a predetermined value and locks up the front suspensions if that value is exceeded. The signals can be provided by an accelerometer, a satellite receiver, wheel/motor speed sensors, sensors in the pumps that signal the specific displacement of the pumps such as their swash plate positions, or memory locations that contain previously calculated specific displacement commands that are used to drive the pumps to a particular specific displacement.

Skid steer vehicle having an anti-diving system

A skid steer vehicle has sprung suspensions that can be locked to prevent vertical movement with respect to the chassis of the vehicle. The operator controls include a switch that the operator can manipulate to lock the suspensions on command. The switch is mounted on a joystick that is used to perform other vehicle functions such as moving the vehicle, raising loader arms, or tilting the bucket or other implement attached to the loader arms. The switch is located on the joystick such that the operator can manipulate the switch without having to remove his hands from the joystick.

Manual suspension locking of a skid steer vehicle having a sprung suspension

A skid steer loader has a chassis with spring-loaded suspensions that are pivotally coupled to the chassis closer to the center of gravity than the wheels. The suspensions include fore-and-aft extending swing arms that pivot about a lateral axis with respect to the chassis. A torsion spring such as a torsion bar is coupled to the control arm to provide torsional support for the suspension. The torsion spring is anchored to the chassis nearer the center of gravity than the point where the swing arm is coupled to the chassis.

Skid steer loader suspension

A skid steer vehicle includes a chassis mounted on four sprung suspensions that are controlled by an electronic controller. The controller monitors the speed of the vehicle and locks the suspensions when the vehicle falls below a predetermined speed.

Skid steer vehicle having suspensions that are locked based on vehicle speed

A skid steer vehicle has a sprung suspension system including four wheels mounted on four swing arms that are pivotally coupled to the chassis of the vehicle. An electronic controller is connected both to position sensors coupled to the swing arms to sense the position of the swing arms and wheels with respect to the chassis and also to hydraulic cylinders that control the position of the swing arms and wheels. The electronic controller determines the average position of each suspension and controls the flow of fluid to the cylinders to keep the swing arms and wheels at their proper target height when vehicle load changes.

Growing community of inventors

Joliet, IL, United States of America

Troy D Bateman