Fanuc Corporation

Toru Shirahata

Tetsuaki Kato

Atsuo Nagayama

Toshihiko Inoue

Masaru Oda

Hiroyuki Kawamura

Kaname Matsumoto

Takatoshi Iwayama

Takayuki Ito

Masaaki Uematsu

Kentarou Ootani

Masayuki Ueno

Kazuto Hirose

A processing machine system includes a processing machine having a machining table, a robot that removes chips produced from processing of the work, a chip collecting hand attached to a distal end portion of the robot to collect the chips, and a robot control unit. The robot control unit acquires a deposition amount of the chips deposited on the machining table, decides whether it is necessary to collect the chips on the basis of the acquired deposition amount. When the chip collection is necessary, the robot control unit operates the robot so as to collect the chips with the chip collecting hand, after the processing is finished.

Processing machine system capable of removing chips produced from machining

A workpiece transfer robot system including a machine tool provided with a workpiece support section and a robot capable of transferring a workpiece relative to the workpiece support section of the machine tool. The machine tool includes a cover surrounding at least the workpiece support section. The cover includes a first side wall provided with a first opening usable for a workpiece transferring task of the robot. The robot includes a track member defining a traveling axis extending in a direction perpendicular to the first side wall of the cover of the machine tool; a slider attached to the track member and capable of traveling along the traveling axis; a first arm attached to the slider and capable of swinging about a first swing axis; a second arm attached to the first arm and capable of swinging about a second swing axis parallel to the first swing axis; and a workpiece hold section provided on the second arm and capable of accessing the workpiece support section through the first opening of the cover of the machine tool.

Workpiece transfer robot system

In a controller for avoiding interference between a mold body comprising a mold and a peripheral equipment installed to said mold and a product removing unit in an injection molding machine, a distance between the position of the mold body and the position of the product removing unit is determined. It is then judged whether or not the distance is smaller than a predetermined distance. If the distance is smaller than the predetermined distance, the operation of product removing unit is decelerated or stopped.

Controller for avoiding interference

A controller for a machine such as a robot and a machine tool having an electric motor as a driving source of the machine, capable of suppressing a natural vibration of the machine and/or an attachment attached to the machine. A frequency or a cycle of the natural vibration of an end effector of the robot as the attachment or the machine itself is determined and a coefficient of a filter for suppressing an amplitude of the natural vibration is altered in accordance with the measured frequency or cycle of the natural vibration. In the case of suppressing a natural vibration of the end effector attached to the robot, frequencies or cycles of natural vibrations of various end effectors in accordance with an operation status of the end effector are determined and stored, and the coefficient of the filter is set in accordance with the stored frequency or cycle of the natural vibration in accordance with the end effector attached to the robot and the operation status. In the case of suppressing a natural vibration of the machine, the natural frequency of the machine is always detected and the coefficient of the filter is automatically altered in accordance with the detected natural frequency, to thereby suppressing an amplitude of the natural vibration of the machine having the natural frequency varying due to variation of load and aging of the machine.

Controller for machine

A robot controller determines an abnormality in position, velocity or acceleration of an end effector or a rotational axis of a robot. The robot controller includes a servo CPU that periodically writes current position data in a shared RAM with a host CPU. The current position data is obtained from robot position sensors. Using the written position data, the host CPU periodically compares stored data corresponding to position, velocity or acceleration with the newly written data. When an abnormal motion is detected, the robot is immediately stopped.

Robot controller

A robot controller resolving a path deviation caused in relation to override processing or temporary stop. A motion planning section constituting software of the robot controller forms a motion plan of a robot with no consideration of overriding and outputs it to an interpolation processing section. The interpolation processing section carries out interpolation processing at each period of calculation processing, calculates a motion amount at each ITP and outputs it to a filtering section. An output filtered for acceleration or deceleration control at the filtering section is processed by an overriding processing section having an operational shutter. An output after the processing to which an override value .beta. (0.ltoreq..beta..ltoreq.1) common to respective axes has been applied is constituted by velocity and acceleration respectively multiplied by .beta. and .beta..sup.2. Acceleration or deceleration of two operation is uniformly exhausted at a corner portion where two operation overlap and, therefore, path error is not caused. Even when overriding is changed in passing through the corner portion, operation is similarly carried out. By gradually changing overriding in deceleration and acceleration before and after a temporary stop, path deviation accompanied by a temporary stop can also be resolved.

Growing community of inventors

Yamanashi, Japan

Toru Shirahata