Denso Corporation

Toyota Jidosha Kabushiki Kaisha

Tomoyuki Koike

Tomohisa Kishigami

Katsumi Kono

Yasuhiro Tanaka

Hiroyuki Mori

Takaaki Tokura

Takeshi Yasuda

Tomohiro Kondo

Masanori Matsubara

Youichirou Suzuki

Noboru Maeda

Masayoshi Satake

Masahiro Kitagawa

Hiroyuki Obata

Naoki Kamikawa

A controller executes a dither control that cyclically increases and decreases an exciting current in a linear solenoid valve so as to vibrate a spool of the linear solenoid valve. A vibration cycle of the spool obtained through the dither control is referred to a dither cycle. The dither control includes a first dither control that vibrates the spool in a first dither cycle and a second dither control that vibrates the spool in a second dither cycle that is shorter than the first dither cycle. The controller executes the first dither control and the second dither control when an oil temperature of the hydraulic oil is between a first oil temperature and a second oil temperature that is higher than the first oil temperature.

Controller and control method for linear solenoid valve

A controller for a linear solenoid valve is configured to: calculate an average value of an exciting current within a period including a natural number multiple of the dither cycle as an average current value; execute a feedback control on a control value of the pulse width modulation signal such that a target value of the exciting current and the average current value match; and calculate a dither correction amount by multiplying a ratio between the control value of the pulse width modulation signal obtained by the feedback control and the average current value by a dither current value that is a current value corresponding to the dither correction amount and calculating the dither correction amount such that an increase in the exciting current due to the dither correction amount is canceled out by a decrease in the exciting current due to the dither correction amount within one dither cycle.

A repeater is used in an in-vehicle communication system for retransmitting communication frames between communication nodes. The repeater includes a storage unit, a retransmission unit, a determiner, and a generator. The storage unit stores a routing map that associates a frame ID that identifies a communication frame from a communication node and a destination of the communication frame. The retransmission unit retransmits the communication frame between the communication nodes based on the routing map stored in the storage unit. The determiner determines whether a preset condition for generating the routing map is satisfied. The generator generates the routing map based on information in the communication frame received from the communication node and stores the map in the storage unit when the determiner determines that the preset condition is satisfied.

Repeater

A relay apparatus connected to communication lines to perform data relay between the communication lines is provided. The relay apparatus includes a receiver unit that receives rewrite information, which includes information for changing setting of the relay apparatus, from a source apparatus via any of the communication lines, a setting changer unit that changes the setting of the relay apparatus in accordance with the rewrite information, and a change information sending unit that sends the rewrite information to another relay apparatus existing in a local network.

Relay apparatus

A relay apparatus for data relay between multiple communication lines includes a sleep relay unit, a start-up determination unit and a communication block unit. The sleep relay unit relays a sleep instruction that instructs a designated apparatus to transition to a sleep mode. The start-up determination unit determines whether or not a start-up apparatus, which is an apparatus other than the designated apparatus and is in a normal mode, exists in a designated communication line, which is a communication line connected to the designated apparatus. Communication that uses the designated communication line is blocked by the communication block unit when it is determined that the start-up apparatus does not exist in the designated communication line.

Switching hubs includes switches in a hierarchy type communication network used in a vehicle, the switches respectively include a first section storing a received Identification (ID) number received by one port in a memory as an identifier of the respective switches, and a second section sending a port-specific identifier from each of the other ports in the respective switches by generating the port-specific identifier as a combination of a port number and the received ID number according to a preset rule, thereby enabling a dynamic assignment of an identifier to each of the switches in the communication network.

Switching hub and communication network

In a receiver circuit, a binary signal is generated based on a signal level of a received signal that has been received via a transmission line from a driver of a transmitter circuit. Then, a first stable state and a second stable state are detected based on a reference signal whose signal level changes in accordance with the received signal. In the first stable state, the received signal is stable at a first signal level. In the second stable state, the received signal is stable at a second signal level. When the first stable state is detected and the received signal is changed from the first signal level into the second signal level, the generated binary signal is retained at a signal level corresponding to the second signal level, until the second stable state is detected.

Receiver circuit

An inter-line switching element formed of a MOSFET is provided between a pair of signal lines. When the level of a differential signal changes from high to low, a control circuit turns on the FET for a fixed period thereby to suppress ringing by decreasing the impedance between the signal lines when the level of the differential signal transitions, and causing the energy of the distortion of the differential signal waveform to be absorbed by the on-resistance of the FET.

Growing community of inventors

Kariya, Japan

Tomoyuki Koike