Impinj, Inc.

Theron Stanford

Christopher J Diorio

Harley K Heinrich

John D Hyde

Jay A Kuhn

Ronald A Oliver

Charles J T Peach

Alberto Pesavento

Scott A Cooper

Shailendra Srinivas

Chad A Lindhorst

Kambiz Rahimi

Matthew Robshaw

Ronald Lee Koepp

Tan Mau Wu

Vadim Lobanov

Amita Patil

Charles Peach

Gregory T Kavounas

Vadim Gutnik

Thomas G Anderl

Joshua F Ensworth

Yael Gregory Maguire

Paul F Dietrich

Aanand Esterberg

Ali Aiouaz

Omer Onen

RFID systems may be configured to use session-dependent replies. When an RFID tag is involved in a certain inventorying session, the tag may respond to inventorying commands with a reply that is at least partly generated based on the session. For example, the tag may generate a reply with a string that has parity based on the session or includes an identifier for the session. The string may be a random number, a tag identifier or item identifier, or any other suitable data sent from the tag.

RFID systems with session-dependent replies

RFID tag ICs in a population can adjust the impedance values used to backscatter-modulate reply signals to increase the distribution or spread of backscattered signal parameters, thereby facilitating the recovery of collided tag replies. An RFID tag IC may adjust its impedance value(s) based on a reader command or independently.

Controlling RFID tag population backscatter characteristics

RFID tags may compensate for non-RFID power sources by automatically enforcing data or state persistence even while powered. A tag may measure a time interval between successive detected modulated reader transmissions. If the interval exceeds a minimum time, then the tag may deassert a protocol flag, erase data, and/or change tag operating states, even if the tag would normally not perform these actions while powered.

RFID tags enforcing persistence while powered

An RFID IC may operate at a relatively low clock frequency while impedance matching to an antenna is being tuned to increase the amount of power that the IC can extract from an incident RF wave. A tuning circuit tunes the impedance matching by adjusting a variable impedance coupling the IC and the antenna. The IC may power-up with a low clock frequency or reduce its current clock frequency to a lower clock frequency prior to tuning or during the tuning process, and may increase its clock frequency upon completion of tuning or during the tuning process.

RFID tag clock frequency reduction during tuning

Embodiments are directed to rectifiers using a single bias current or bias current path to bias multiple rectifying elements. A rectifier that has multiple rectifier stages coupled together serially includes a bias current path coupled to each of the rectifier stages. Thee bias current path is configured to simultaneously bias rectifying elements in each of the rectifier stages by using a bias current to bias a first rectifying element and reusing the bias current to bias other rectifying elements.

RFID tag rectifiers with bias current reuse

RFID ICs sense and indicate changes in their surrounding environment, such as changes in temperature, humidity, chemical presence, RF signals, and similar. An RFID IC indicates when a significant environmental change has occurred, for example by adjusting the value of a flag, writing data to memory, transmitting a message to an external entity, exiting a sleep state, and/or responding repeatedly to an inventorying reader. In some cases, RFID IC actively notifies an external entity that a significant environmental change has been sensed. For example, RFID IC may alert the external entity by participating in a special inventory process meant for RFID ICs sending environmental change. The RFID IC may alert the external entity by interjecting itself into an inventory round, re-participating in an inventory round, refraining from entering a sleep state after inventorying, and/or adjusting timing of a scheduled reply to communicate with an RFID reader ahead of schedule.

Environment-based RFID IC behavior

Embodiments are directed to rectifiers using a single bias current or bias current path to bias multiple rectifying elements. A rectifier that has multiple rectifier stages coupled together serially includes a bias current path coupled to each of the rectifier stages. The bias current path is configured to simultaneously bias rectifying elements in each of the rectifier stages by using a bias current to bias a first rectifying element and reusing the bias current to bias other rectifying elements.

Growing community of inventors

Seattle, WA, United States of America

Theron Stanford