Texas Instruments Corporation

Suvadip Banerjee

Anant Shankar Kamath

Sreeram Subramanyam Nasum

Kumar Anurag Shrivastava

Tarunvir Singh

Swaminathan Sankaran

Robert Floyd Payne

Siraj Akhtar

John Paul Tellkamp

Mark Edward Wentroble

Rakesh Hariharan

Kishalay Datta

Kashyap Jayendra Barot

Srinivasa Rao Madala

Prajkta Vyavahare

Anandha Ruban Tiruchengode Tirumurugga Bupathi

Arun Adoni

Rr Manikandan

Sudhir Komarla Adinarayana

Gurumurti Kailaschandra Avhad

In described examples, a converter circuit includes a primary-side ground, a current sensor, a control signal generator, first and second control switches, and a transformer with a center-tapped primary-side coil. A first terminal of the first control switch is coupled to a first terminal of the coil and a first input of the current sensor. A first terminal of the second control switch is coupled to a second terminal of the coil and a second input of the current sensor. Second terminals of the first and second control switches are coupled to ground. The control signal generator closes the first control switch and opens the second control switch in a first phase; opens the first control switch and closes the second control switch in a second phase that alternates with the first phase; and adjusts first phase duration in response to current sensor output, without changing converter period duration.

Push-pull converter with saturation prevention

Circuits and systems include a parallel resistor-capacitor (RC) network coupled between a pin and ground, and first and second transistors coupled in source follower configuration with a common gate coupling. The source of the first transistor is coupled to the pin. A first switch couples a drain of the first transistor to the common gate coupling during soft-start (SS) and decouples that connection during over current limit (OCL) sensing, and a second switch couples a drain of the second transistor to the common gate coupling during OCL sensing and decouples that connection during SS. A first current source is enabled deliver a constant current to the pin during SS. A second current source is enabled to generate a reference voltage at the source of the second transistor during OCL, which reference voltage is transferred to the pin by the source follower configuration. A comparator controls the switches to transition from SS to OCL sensing. The comparator output signal is based on a comparison of the voltage at the pin to a threshold voltage.

Multifunction pin for soft start and current limit in voltage converters

Examples of clock generators with very low duty cycle distortion (DCD) are provided. A clock source and driver generate a main clock signal and a complementary clock signal that are input to a chopper circuit, which also receives complementary chopper control signals from a non-overlapping generator circuit. The chopper circuit is controlled to pass the main clock signal as a first output signal when the chopper circuit is in a first state, and pass the complementary clock signal as a second output signal when the chopper circuit is in a third state. In a second state, which occurs during each of the falling edges of the main clock signal, the chopper circuit holds the previous state, and does not transmit the falling edges of the main clock signal. The rising edges of the main clock signal is used to derive the rising and falling edges of the output signals.

Low DCD clock signal generators

A communication interface buffer comprises: a data bus connection adapted to be coupled to a bus interface contact; and a ground. The communication interface buffer also comprises an output transistor with a first current terminal, a second current terminal and a control terminal, the first current terminal coupled to the data bus connection, the second current terminal coupled to ground, and the control terminal adapted to receive a drive signal. The communication interface buffer also comprises a control circuit coupled to the control terminal of the output transistor, wherein the control circuit is configured to: turn off the output transistor during a first interval that starts when the data bus connection is coupled to the bus interface contact; and turn on the output transistor after the first interval is complete.

Communication interface buffer with hot-swap protection

A system includes a switching converter, an input voltage source coupled to an input of the switching converter, and a load coupled to an output of the switching converter. The system also includes a load sense circuit coupled to the load and configured to provide a load sense signal. The system also includes an oscillator coupled to the switching converter and configured to provide a spread spectrum modulated (SSM) clock signal to the switching converter, wherein a frequency of the SSM clock signal varies as a function of the load sense signal.

Load adaptive spread spectrum modulation (SSM)

In described examples, an integrated circuit includes an on-off keying (OOK) digital isolator, which includes a first circuitry, a multiplexer, an OOK modulator, an isolation barrier, an OOK envelope detector, and a second circuitry. The first circuitry generates and outputs a calibration signal. The multiplexer has a data signal input, and an input coupled to a first circuitry output. An OOK modulator input is coupled to a multiplexer output. An isolation barrier input is coupled to an OOK modulator output. An OOK envelope detector input is coupled to an isolation barrier output. The second circuitry includes an input coupled to an OOK envelope detector output, and an output coupled to an OOK envelope detector control input. The second circuitry detects a duty cycle distortion (DCD) of the OOK envelope detector output, and outputs a control signal to change the OOK envelope detector output's duty cycle based on the detected DCD.

Self-calibrating on-off keying based digital isolator

An electronic device includes one or more multinode pads having two or more conductive segments spaced from one another on a semiconductor die. A conductive stud bump is selectively formed on portions of the first and second conductive segments to program circuitry of the semiconductor die or to couple a supply circuit to a load circuit. The multinode pad can be coupled to a programming circuit in the semiconductor die to allow programming a programmable circuit of the semiconductor die during packaging. The multinode pad has respective conductive segments coupled to the supply circuit and the load circuit to allow current consumption or other measurements during wafer probe testing in which the first and second conductive segments are separately probed prior to stud bump formation.

Multi-function bond pad

An apparatus includes a first control circuit having an output and including a first comparator and a second control circuit coupled to the output of the first control circuit. The second control circuit includes a second comparator configured to: compare a first value to a reference frequency value, the first value indicating a frequency of a signal at the output of the first control circuit; and provide an adjustment value to change a hysteresis window of the first comparator.

Adaptive hysteretic control for a power converter

A device includes a transformer that further includes a primary and a secondary windings. A switch is coupled to the primary winding, and this switch is controlled by the received digital input signal. An oscillator is further formed on the secondary winding where the oscillator oscillates in response to variations of the received input signal. A detector coupled to the oscillator will then detect the oscillations in response to the variations of the received input signal. Thereafter, the detector generates a digital output based on the detected oscillations.

Galvanic isolation in devices

A system includes a controller for automated test equipment (ATE) contactor to interface with a device under test (DUT) including a power converter having a primary and secondary side, each side has an input/output (I/O) pin. The controller causes the ATE contactor to apply a load current on the secondary side of the power converter at a first value and vary the load current to a second value. The contactor receives first and second indications, at the first and second load currents, of a voltage on the primary side I/O pin, a voltage on the primary side of the power converter, an input current on the primary side of the power converter, a voltage on the secondary side I/O pin, and a voltage on the secondary side of the power converter. The controller determines a primary and secondary side ATE contactor resistances based on the first and second indications.

Growing community of inventors

Bengaluru, India

Suvadip Banerjee