Toyota Jidosha Kabushiki Kaisha

Denso Corporation

Sumiko Amamiya

Shigeru Kamio

Yasuhiro Nakai

Kazuo Kawaguchi

Tatsuya Ozeki

Yasuo Shimizu

Yuji Inoue

Taku Itoh

Yasushi Kobiki

Kenichi Fujiki

Keijiro Ohshima

Koichiro Muta

Yuichiro Kitamura

An HV_ECU executes a program including a step of calculating an estimated gradient, a step of performing rate limit processing on a change in the estimated gradient when on a hill and an absolute value of the vehicle speed is equal to or below V(), a step of performing hysteresis processing, a step of calculating a creep increase coefficient, and a step of calculating a creep increase torque.

Control apparatus and control method of a vehicle

A hybrid vehicle is provided with means for setting a four-wheel drive condition which is a condition for switching from two-wheel drive to four-wheel drive, and an EV switch which, when turned on by an occupant of the vehicle, places the vehicle in an EV driving mode in which only an electric motor is used as the power source. The four-wheel drive condition setting means changes the four-wheel drive condition to reduce a region in which the vehicle operates in four-wheel drive when the EV switch is on as compared to when the EV switch is off. As a result, the vehicle operates in two-wheel drive more frequently, thus reducing power consumption.

Hybrid vehicle and control method thereof

Presence/absence of a failure in a feedback control system of a motor is monitored. When a failure is detected in the feedback control system, the motor is driven by switching to an open-loop control. During the open-loop control, the motor is rotated by sequentially switching the motor current supply phase without feeding back encoder count information. The position count is incremented or decremented every time the current supply phase is switched. When the position count has reached a target count, it is determined that the rotor has reached a target position, whereupon the open-loop control is finished.

Motor control apparatus

In an automatic transmission position control by a motor, it is determined whether the present instant belongs to a starting period, that is, the present instant is immediately after resetting of a control unit or application of power to it. If it is the starting period, an actual shift position that is detected from an output of an output shaft sensor for detecting a rotation position of a motor is set as an instructed shift position. With this measure, even if the control unit is reset for a certain reason while the vehicle is running, the instructed shift position is not changed in association with the resetting. This prevents trouble that the shift position is switched contrary to the intention of the driver, whereby the reliability of a position switching control can be increased.

A shift control system rotates an actuator to cause a wall of a detent plate to contact a roller of a detent spring, and detects the position of contact so as to detect the position of the wall of the detent plate. This wall position is set as a reference position of the actuator. Accordingly, the rotation of the actuator can appropriately be controlled even if an encoder which can only detect relative positional information is employed, and thus the shift range can appropriately be switched.

Shift control system, shift control method and shift switching device

Shift control system, shift control method, and shift switching device

A shift control system rotates an actuator to allow a wall of a detent plate and a roller of a detent spring to contact each other and then detects the position of contact so as to detect the position of the wall of the detent plate. After the wall position is determined, the actuator is driven in the direction opposite to the wall until the actuator reaches a position located before the wall position and distant therefrom by a predetermined amount, in order to cancel flexure or extension of the detent spring that is caused when the detent spring is pushed against the wall of the detent plate. Accordingly, such a situation where the shift position is moved by the recovery force of the detent spring can be avoided.

Shift control system and shift control method

A P-ECU controls an actuator which drives a shift control mechanism. An encoder signal acquisition unit acquires signals output from an encoder which detects a rotational angle of the actuator. A counter calculates a count value from the output signals of the encoder. An energization control unit controls energization to the actuator. A first phase-matching unit uses the Z-phase signal of the encoder to match the count value with energized phases so as to find a correspondence therebetween and a second phase-matching unit matches the count value with energized phases to find a correspondence therebetween without using the Z-phase signal of the encoder. If the first phase-matching unit detects an abnormality of the encoder, the second phase-matching unit subsequently performs phase matching.

Rotating-body control device

A P-ECU determines whether or not energization to an actuator is shut off when a shift-range switch instruction is unissued. If energization to the actuator is shut off, the P-ECU obtains a current rotational position of the actuator according to a count value obtained by an encoder. If a difference between a target rotational position and the current rotational position exceeds a predetermined amount, positional correction control is exercised.

In a motor-driven shift position switching device, when the difference between a target position and the rotation position of a rotor has become smaller than a prescribed value in a motor feedback control, a transition is made to a deceleration control. A phase lead correction amount for correcting the phase lead of the current supply phase with respect to the rotor rotation phase is set in accordance with the rotor rotation speed. Thus, proper braking force suitable for the rotor rotation speed is exerted on the rotor and the rotor can be decelerated smoothly as it approaches the target position. Further, in the period when the current supply to the motor is kept off, the shift position switching determination ranges are set wider than in the period when the current supply to the motor is on.

Growing community of inventors

Okazaki, Japan

Sumiko Amamiya