Power Integrations, Inc.

Ciena Corporation

Steven Greig Porter

Hartley Fred Horwitz

Robert J Mayell

Sorin Stefan Georgescu

Roger Colbeck

Yueming Wang

Robert W Busse

Paul Walter DeMone

A controller includes first and second half bridge sense circuits coupled to a half bridge node. The half bridge node is coupled between a high side switch and a low side switch coupled to an input. A rising slew detection circuit is coupled to the first half bridge sense circuit to output a first slew detection signal in response to a rising slew event at the half bridge node. A falling slew detection circuit is coupled to the second half bridge sense circuit to output a second slew detection signal in response to a falling slew event at the half bridge node. A control circuit coupled to output a high side drive signal to the high side switch and a low side drive signal to the low side switch in response to the first slew detection signal, the second slew detection signal, and a feedback signal.

Deadtime adjustment for a power converter

A method to control a high side switch of a motor drive includes sinking a current of an ON signal to communicate a turn ON of the high side switch. A first current signal, a second current signal, a third current signal, a fourth current signal and a common mode rejection signal are generated in response to the ON signal. The ON signal in a presence of common mode noise is determined by comparing the first current signal and the second current signal. A first output signal is generated in response to determining the ON signal. A drive signal is generated responsive to the first output signal to control the high side switch in response to the ON signal in presence of common mode noise that is caused by a slewing at a half-bridge node.

High side signal interface in a power converter

A controller for use in a power converter of a motor drive includes a control circuit configured to turn ON a high side switch by sinking a current of an ON signal. A high side signal interface circuit is coupled to receive the ON signal to generate a drive signal to control switching of the high side switch in a presence of a common mode signal caused by slewing at a half bridge node. The high side signal interface circuit includes a common mode cancellation circuit coupled to provide a common rejection signal to provide a cancellation or rejection of the common mode signal. A first current hysteresis comparator is coupled to receive a common mode rejection signal, a first current signal, and a fourth current signal, and generate a first output signal in a presence of a common mode voltage.

A power converter controller includes a high side signal interface circuit that includes a common mode cancellation circuit that is coupled to generate a fourth current signal representative of an OFF signal referenced to a bypass voltage during an initial state, and a first current signal in response to an ON signal being pulled to a lower value relative to the OFF signal to turn ON a high side switch. The common mode cancellation circuit generates a common mode rejection signal in response to the first and fourth current signals. A first current hysteresis comparator receives the first and fourth current signals, the common mode rejection signal, and a drive signal to generate a first output signal. A drive signal generated in response to the first output signal in a presence of a common mode voltage caused by slewing at a half bridge node.

A controller for use in a power converter includes a control circuit coupled to generate a low side drive signal to control switching of a low side switch, and generate an ON signal and an OFF signal in response to a feedback signal representative of an output of the power converter. A high side signal interface circuit is coupled to generate a high side drive signal in response to the ON signal and the OFF signal to control switching of a high side switch. The ON signal and the OFF signal are coupled to be pulled up in response to a bypass voltage during an initial state. The high side signal is coupled to turn on the high side switch in response to the control circuit pulling the ON signal low, and turn off the high side switch in response to the control circuit pulling the OFF signal low.

A system and a method selectively switch between two different voltage supplies supplying a common node. A first of the voltage supplies is coupled to the common node by a first switch and a second of the voltage supplies is coupled to the common node by a second switch. The switching device comprises: a feedback network comprising a high-pass filter for filtering a signal at the common node and outputting the filtered signal as a feedback signal; a timing controller coupled to at least one of the first and second voltages supplies for determining when to switch between said first and second power supplies; a ring switch controller for applying a first control signal to the first switch for selectively enabling and disabling the first switch in response to the timing controller and the feedback signal; and a battery switch controller for applying a second control signal to the second switch for selective enabling and disabling the second switch in response to the timing controller and the feedback signal. The method comprises the steps of: receiving a request to switch between the first and second voltage supplies; gradually removing the voltage supply coupled to the common node; gradually applying the other of said voltage supplies; and filtering a signal at said common node for detecting noise.

Growing community of inventors

Nepean, Canada

Steven Greig Porter