Northeastern University

Sivasubramanian Somu

Ahmed Busnaina

Cihan Yilmaz

Jun Huang

TaeHoon Kim

Xugang Xiong

Nicol E McGruer

George G Adams

Hanchul Cho

Peter Ryan

Asli Sirman

Taehoon Kim

Yung Joon Jung

Jin Young Lee

Vladimir P Torchilin

Tiziana Musacchio

Young Lae Kim

Moneesh Upmanyu

Asanterabi Malima

Salome Siavoshi

Aniket Datar

Jaydev Upponi

Laila Jaberansari

A variety of homogeneous or layered hybrid nanostructures are fabricated by electric field-directed assembly of nanoelements. The nanoelements and the fabricated nanostructures can be conducting, semi-conducting, or insulating, or any combination thereof. Factors for enhancing the assembly process are identified, including optimization of the electric field and combined dielectrophoretic and electrophoretic forces to drive assembly. The fabrication methods are rapid and scalable. The resulting nanostructures have electrical and optical properties that render them highly useful in nanoscale electronics, optics, and biosensors.

Three-dimensional crystalline, homogeneous, and hybrid nanostructures fabricated by electric field directed assembly of nanoelements

Damascene templates have two-dimensionally patterned raised metal features disposed on an underlying conductive layer extending across a substrate. The templates are topographically flat overall, and the patterned conductive features establish micron-scale and nanometer-scale patterns for the assembly of nanoelements into nanoscale circuits and sensors. The templates are made using microfabrication techniques together with chemical mechanical polishing. These templates are compatible with various directed assembly techniques, including electrophoresis, and offer essentially 100% efficient assembly and transfer of nanoelements in a continuous operation cycle. The templates can be repeatedly used for transfer of patterned nanoelements thousands of times with minimal or no damage, and the transfer process involves no intermediate processes between cycles. The assembly and transfer processes employed are carried out at room temperature and pressure and are thus amenable to low cost, high-rate device production.

Damascene template for directed assembly and transfer of nanoelements

A method for high rate assembly of nanoelements into two-dimensional void patterns on a non-conductive substrate surface utilizes an applied electric field to stabilize against forces resulting from pulling the substrate through the surface of a nanoelement suspension. The electric field contours emanating from a conductive layer in the substrate, covered by an insulating layer, are modified by a patterned photoresist layer, resulting in an increased driving force for nanoelements to migrate from a liquid suspension to voids on a patterned substrate having a non-conductive surface. The method can be used for the production of microscale and nanoscale circuits, sensors, and other electronic devices.

High rate electric field driven nanoelement assembly on an insulated surface

A single-walled carbon nanotube-based micron scale multiplex biosensor is provided that enables the detection of glucose, lactate, and urea. The sensor is based on modification of semiconducting single-walled carbon nanotubes using a linker that non-covalently associates with the nanotubes and covalently couples to an enzyme. Reaction of a physiological substrate with the enzyme results in increased resistance of the nanotubes within the sensor. The sensor is suitable for use in patient monitoring, particularly in a clinical setting. Incorporation of read out electronics and an RF signal generator into the sensor device enables it to communicate to a relay station or remote receiver. Methods are also provided for fabricating the biosensor device and using the device for detection.

Single-walled carbon nanotube biosensor for detection of glucose, lactate, and urea

The invention provides a fast, scalable, room temperature process for fabricating metallic nanorods from nanoparticles or fabricating metallic or semiconducting nanorods from carbon nanotubes suspended in an aqueous solution. The assembled nanorods are suitable for use as nanoscale interconnects in CMOS-based devices and sensors. Metallic nanoparticles or carbon nanotubes are assembled into lithographically patterned vias by applying an external electric field. Since the dimensions of nanorods are controlled by the dimensions of vias, the nanorod dimensions can be scaled down to the low nanometer range. The aqueous assembly process is environmentally friendly and can be used to make nanorods using different types of metallic particles as well as semiconducting and metallic nanotubes.

Nanoscale interconnects fabricated by electrical field directed assembly of nanoelements

A carbon nanotube-based micron scale chemical sensor or sensor array is provided that enables the remote detection of hydrogen sulfide and other chemicals in a gas stream. The sensor is suitable for use in harsh environments of high temperature and pressure such as those encountered during petrochemical exploration and recovery. Multiplex sensor devices detect two or more chemical agents simultaneously, or they can detect conditions such as pressure, salinity, humidity, pH, or scale-forming ions. Incorporation of read out electronics and an RF signal generator into the sensor device enables it to communicate to a relay station or receiver for 3D mapping or other analysis. Methods are also provided for fabricating the chemical sensor device and using the device for detection.

Chemical sensor based on highly organized single walled carbon nanotube networks

A non-volatile bistable nano-electromechanical switch is provided for use in memory devices and microprocessors. The switch employs carbon nanotubes as the actuation element. A method has been developed for fabricating nanoswitches having one single-walled carbon nanotube as the actuator. The actuation of two different states can be achieved using the same low voltage for each state.

System and method for integrating a single nanowire into a nanocircuit

The invention provides a fast, scalable, room temperature process for fabricating metallic nanorods from nanoparticles or fabricating metallic or semiconducting nanorods from carbon nanotubes suspended in an aqueous solution. The assembled nanorods are suitable for use as nanoscale interconnects in CMOS-based devices and sensors. Metallic nanoparticles or carbon nanotubes are assembled into lithographically patterned vias by applying an external electric field. Since the dimensions of nanorods are controlled by the dimensions of vias, the nanorod dimensions can be scaled down to the low nanometer range. The aqueous assembly process is environmentally friendly and can be used to make nanorods using different types of metallic particles as well as semiconducting and metallic nanaotubes.

Methods for fabricating templates for nanoelement assembly and methods for fluid-guided assembly of nanoelements are provided. Templates are fabricated by plasma modification of surface hydrophilicity and production of a network of hydrophobic trenches having a hydrophilic bottom surface. Single-walled carbon nanotubes (SWNT) can be assembled into stable films, ribbons, and wires of nanoscale thickness and nanoscale or microscale width and length. The nanofilm assemblies prepared according to the invention are highly conductive and can be used in the fabrication of a wide variety of microscale and nanoscale electronic devices.

Highly organized single-walled carbon nanotube networks and method of making using template guided fluidic assembly

Nanosubstrates as biosensors, methods of making such nanosubstrates, and methods of using such nanosubstrates to detect biomarkers are described.

Growing community of inventors

Natick, MA, United States of America

Sivasubramanian Somu