Mitsubishi Electric Corporation

Sony Corporation

National Institute for Materials Science

Electric Power Development Co., Ltd.

Shinsuke Suzuki

Yuji Zushi

Koji Hashimoto

Akihiro Ishii

Hiroshi Harada

Katsuya Nakamoto

Toshiharu Kobayashi

Tadaharu Yokokawa

Kyoko Kawagishi

Shoso Tsunekazu

Michinari Yuyama

Makoto Osawa

Yuichiro Joh

Satoshi Utada

Shiro Nagano

A method for recycling a Ni-based single crystal superalloy part or unidirectionally solidified superalloy part provided with a thermal barrier coating containing at least a ceramic on a surface of a Ni-based single crystal superalloy substrate or Ni-based unidirectionally solidified superalloy substrate, in which the method including the steps of: melting and desulfurizing a Ni-based single crystal superalloy part or Ni-based unidirectionally solidified superalloy part at a temperature of the melting point or more of the Ni-based single crystal superalloy or Ni-based unidirectionally solidified superalloy and less than the melting point of the ceramic; heating a casting mold for a recycled Ni-based single crystal superalloy part or casting mold for a recycled Ni-based unidirectionally solidified superalloy part to a temperature of the melting point or more of the Ni-based single crystal superalloy or Ni-based unidirectionally solidified superalloy; pouring the desulfurized melted Ni-based single crystal superalloy or Ni-based unidirectionally solidified superalloy into the casting mold, and producing a melting stock or growing a Ni-based single crystal superalloy or Ni-based unidirectionally solidified superalloy; and removing the melting stock or the recycled Ni-based single crystal superalloy part or recycled Ni-based unidirectionally solidified superalloy part from the casting mold. In this way, a method for recycling a Ni-based superalloy part, by which the recycle cost of a Ni-based superalloy part and the lifetime cost of a highly efficient gas turbine engine using a Ni-based superalloy part can be significantly reduced, and further a Ni-based superalloy part having the same high-temperature strength and oxidation resistance as those of a newly produced Ni-based superalloy part can be obtained, is provided.

Ni-based superalloy part recycling method

A thermal power plant has an exhaust gas system, a feed-water system, a high-pressure feed-water heater provided to the feed-water system, a main economizer, a catalytic NOx removal equipment, and a sub economizer. The main economizer is provided to the secondary side of the high-pressure feed-water heater of the feed-water system and increases the temperature of the feed-water by using the residual heat of the combustion gas from the boiler. The catalytic NOx removal equipment is provided to the secondary side of the main economizer of the exhaust gas system. The exhaust gas is supplied to the catalytic NOx removal equipment at a required temperature or higher. The sub economizer is provided between the high-pressure feed-water heater and the main economizer and increases the temperature of water by using the exhaust gas on the secondary side of the NOx removal equipment.

Fossil-fuel power plant and fossil-fuel power plant operation method

Provided is a drive control device capable of surely detecting, by a monitoring/controlling unit, an abnormality of a short circuit and a disconnection in a power supply circuit to an electric load, and of decreasing a load required for a quick response imposed on the monitoring/controlling unit. A switching element is controlled to open/close by a control output signal generated by a monitoring/controlling unit, and a determination storing circuit determines whether circuit opening and circuit closing have been correctly carried out and stores a result of the determination, and periodically reports to the monitoring/controlling unit. While the stored content of the determination is periodically reset, the determination operation is updated and continues. The monitoring/controlling unit does not need to immediately monitor the determination storing signal when the open/closing command is generated.

Drive control device for an electric load

An electronic control apparatusA is configured in such a way that a CPUA reads the conduction current of an opening/closing devicein an IPMA, by way of serial-parallel convertersandand a second multi-channel A/D converter; the opening/closing deviceis opening/closing-controlled through a serial control signal SRn or a parallel control signal PWMn; and a reading timing control circuitadjusts the reading timing in such a way that, regardless of the kind of the control signal, reading is performed during the period in which the opening/closing deviceis driven to be closed. As a result, the serial-parallel converter can reduce the number of wiring leads between the IPM and the microprocessor, and the digital conversion value is accurately read, by adjusting the error between the serial-signal timing and the parallel-signal timing.

Electronic control apparatus

The invention improves safety of an electronic controller using a nonvolatile memory MRAM able to easily perform reading and writing operations at high speed. Therefore, MRAM for writing a control program from an external tool has a correction code adding writing circuit, a decoding reading-out circuit, and error registers for writing an error generating address number thereto as error data. When the error generating address is designated and confirmation reading-out is performed and an error is generated as before, an overlapping abnormality judgment is made and abnormality notification is performed. A program memory area of MRAM is normally in a writing inhibition state. When the external tool is connected, the inhibition state is released. The error registers are arranged in a data memory area set to no writing inhibition object.

Electronic controller

A display control device for controlling the display of an image in a display device includes a decision unit configured to decide whether the state of a scaling of a moving-image portion in a display object image or an image to be displayed in the display device has changed; and a display control unit configured to select a screen mode for displaying the display object image in response to the change in the scaling state of the moving-image portion in the display object image, and to display the display object image in the screen mode in the display device.

Display control device, display control method, and program

An analog input signal obtained from an analog sensor groupA and first and second calibration voltages obtained by high-precision voltage-dividing resistors are successively selected by a multiplexer, digitally converted through an AD converter and then input to a microprocessor. The microprocessor calculates a collinear approximate coefficient based on the first and second calibration voltages in cooperation with a program memory, and corrects the digital conversion value to the analog input signal by using the approximate coefficient, thereby correcting a linear error of the conversion characteristic of the AD converter. In the calculation of the approximate coefficient, upper and lower limit check is executed on measurement values and calculation coefficients, and also plural calculation results are averaged to enhance the precision.

Growing community of inventors

Tokyo, Japan

Shinsuke Suzuki