Microchip Technology Inc.

Ruan Lourens

Sean Steedman

Vivien Neil Delport

Richard L Hull

James B Nolan

Jerrold S Zdenek

Thomas Youbok Lee

Zacharias Marthinus Smit

Russell E Cooper

Layton W Eagar

Miguel Moreno

Steve Vernier

Alan Lamphier

Razvan Enachescu

Michael Charles

Marc Tiu

Glen Allen Sullivan

A power element bypass and voltage regulation circuit shutdown is used in a low drop out (LDO) bypass voltage regulator to minimize current drawn by the voltage regulator circuit when the supply input voltage approaches the regulated output voltage of the voltage regulation circuit. Two modes of operation are used in the low drop out (LDO) bypass voltage regulator. A regulate mode is used when the supply input voltage is greater than the reference voltage input, and a track mode is used when the supply input voltage is less than or equal to approximately the regulated output voltage of the voltage regulation circuit. Hysteresis may be introduced when switching between the regulate and track modes of operation.

Low drop out (LDO) bypass voltage regulator

An integrated circuit device provides a choice of external pins (connections) that may be user selectable for coupling an external filter/stabilization capacitor to an internal voltage regulator. However, connecting the output of a internal voltage regulator to an uncharged external filter/stabilization capacitor (or to a capacitor charged to a different voltage level than the internal regulation voltage) through a low impedance path can cause the regulator output voltage to sag/spike if the internal voltage regulator tries to charge/discharge the capacitor up/down to equilibrium with the regulator output voltage. To minimize this potential sag/spike, the voltage on the external filter/stabilization capacitor may be adjusted in a controlled manner to substantially the same voltage as the voltage on the output of the internal voltage regulator, and then the internal voltage regulator is operationally coupled through a low impedance to the external regulator filter/stabilization capacitor.

Connection of an internal regulator to an external filter/stabilization capacitor through a selectable external connection and prevention of a current surge therebetween

A multi-channel remote keyless entry (RKE) transponder having dynamically re-configurable input channel selection, channel disable, settable sensitivity for each channel, wake-up filter timing parameters, automatic gain control hold, internal tuning capacitor selection for each channel's antenna, minimum modulation depth requirement for input signal and bi-directional talk-back. Programmable minimum modulation depth requirement reduces false wake-up of the RKE transponder. An antenna for each channel of the RKE transponder may be tuned with internal tuning capacitors for improved range and receiver sensitivity. The internal tuning capacitor parameters may be stored in a configuration register. Gain of the channel may be fixed while the antenna is tuned. The antennas may be de-queued for talk-back to a base station for low frequency bi-directional communications. An external control device may dynamically read from and write to the configuration registers via a serial communications interface.

Dynamic configuration of a radio frequency transponder

A brown-out-reset circuit having programmable power and response time characteristics. These characteristics may be programmed over an n-bit wide bus for 2different characteristics ranging from very low power consumption and slower response time to very fast response time and higher power consumption. A serial one wire bus may be used instead of the n-bit wide bus.

Variable power and response time brown-out-reset circuit

A time signal receiver and decoder receives, detects and stores time information from time signals, e.g., WWV, WWVH, WWVB (USA), JJY (Japan), MSF (UK) and the like. The time information may be used for a self setting clock, and the clock may be used as a reference in time sensitive applications, devices and systems. The time signal receiver may use a high-Q state variable bandpass filter or an anti-notch filter circuit for selectivity at the time signal frequency of interest. The decoder is coupled to the time signal receiver, decodes the time information in the received time signal and may store the decoded time information.

Time signal receiver and decoder

A super-regenerative receiver uses controlled Q-quenching and may limit the resonant tank circuit amplitude by loading the tank circuit as soon as regenerative oscillation is detected. An amplitude detector is coupled to the regenerative amplifier and controls a Q loading circuit coupled to the tank circuit of the regenerative amplifier. The amplitude detector turns on the Q loading circuit which then stops the regenerative amplifier from oscillating, and the Q-loading remains on for a brief time to insure that the regenerative amplifier has stopped oscillating. After the brief time, the Q loading circuit is turned off and the regenerative amplifier goes into oscillation again. This cycle repeats controllably over and over, resulting in a lower self-induced noise floor and improved received signal sensitivity. The super-regenerative receiver may be used in the very low frequency (VLF), low frequency (LF), medium frequency (MF), high frequency (HF), very high frequency (VHF) and super high frequency (SHF) ranges to receive continuous wave (CW), amplitude modulated (AM) and frequency modulated (FM) radio signals.

Q-quenching super-regenerative receiver

An Ultra-low power voltage detection circuit is implemented in a digital integrated circuit to device to provide a basic timer, programmable timer and programmable low voltage detection (PLVD) using a single connection of the digital integrated circuit device and a passive component(s) external to the digital integrated circuit device. An internal low current source may be enabled so as to discharge an external timing capacitor connected to the output connection, thus eliminating the need for an external resistor. However, timing accuracy may be improved by adding an external discharging resistor and/or charging resistor. The output connection may be configured as a tri-state output and may be driven high to charge and low to discharge the timing capacitor. A voltage reference may be used in determining a voltage trip point for timing and low voltage detection purposes. Temperature may be determined from either a trip voltage compared to a known voltage determined at a known temperature, or a current value of the current source compared to a known current value determined at a known temperature, times a constant.

Growing community of inventors

Chandler, AZ, United States of America

Ruan Lourens