Gm Global Technolgoy Operations, Inc.

Ronald W Van Diepen

Joseph M Stempnik

Christopher E Whitney

Mark Henry Costin

Matthew D Whitton

Ning Jin

Bryan D Lehman

Paul Alan Bauerle

Steven Patrick Moorman

Michael Livshiz

Jeffrey M Kaiser

Richard B Jess

Robert Charles Simon, Jr

Xuefeng Tim Tao

Daniel P Grenn

Todd R Shupe

Kevin M Baltes

Vivek Mehta

Klaus Pochner

Christopher Harold Knieper

Etsuko Muraji Stewart

Jinchun Peng

Michael A Turley

Jun Lu

Mateusz M Nowak

Harinath Atmaram

Helmut Oswald

Jonathan Packard

Enrico Tropschug

Tracey A Bagley-Reed

Sandra J Nelson

Xuehan Kong

Madhura N Paranjape

Jeffrey M DeSimone

A method and system for selecting a speed ratio for a continuously variable transmission (CVT) of a vehicle during braking. The method and system includes determining a Current Actual Speed Ratio of the CVT when the distance of a brake pedal travel exceeds a predetermined distance, determining, by a transmission control module (TCM), an amount of Available Speed Ratio Change (&#x394;r), a Current Ratio Change Capability (Current-{dot over (r)}), and a Predictive Ratio Change Capability (Predictive-{dot over (r)}). The method further includes the TCM calculating a Time to Reach the Minimum Under-drive Ratio (t), calculating a Predicted Velocity of the Vehicle (v) using (t), determining a Desired Speed Ratio of the CVT using the Predicted Velocity of the Vehicle (v), and actuating the CVT to the Desired Speed Ratio.

Ratio selection method for a continuously variable transmission during deceleration by braking

A vehicle includes an engine, dual-clutch transmission (DCT), and controller. The controller executes a method to control a requested change-of-mind shift of the DCT to a second desired gear state. The requested shift is initiated after a prior-requested but not yet fully-executed shift of the DCT to a first desired gear state. The controller detects the requested shift, identifies the second desired gear state, and aborts the prior-requested shift immediately upon identifying the second desired gear state. The controller also shifts the DCT to the second desired gear state using a calibrated shift profile corresponding to the detected shift. The calibrated shift profile describes required oncoming and offgoing clutch torques needed for achieving the second desired gear state. Engine speed control may be used to synchronize engine and input shaft speeds.

Change-of-mind shift control of a dual-clutch transmission

A method of commanding a synchronous gear shift begins by receiving a request to shift from a third gear to a first gear, and skipping a second gear having a gear ratio between the gear ratio of the first gear and the gear ratio of the third gear. Subsequently the method includes: reducing a torque command to a predetermined value; opening a clutch disposed on the input shaft of the transmission to decouple the transmission from the engine; transitioning the engine from a torque-control mode into a speed-control mode; commanding the engine to rotate at a speed dictated by the motion of the vehicle and the gear ratio of the first gear; closing the clutch to couple the transmission and the engine; and transitioning the engine back into the torque-control mode.

Automatic transmission synchronous gear shift

An engine control system for a vehicle includes a power request determination module, a desired speed determination module, and a torque control module. The power request determination module determines a power request for an engine based on a request from a driver of the vehicle and a speed of the vehicle. The desired speed determination module determines a desired speed of the engine based on a speed of a turbine in a torque converter of the engine, a state of a clutch in the torque converter, and one of the power request, a first amount of clutch slip, and a second amount of clutch slip. The torque control module determines a desired engine torque based on the desired engine speed and the power request and controls torque output of the engine based on the desired engine torque.

System and method for controlling engine torque

An engine control system comprises a pedal torque determination module, a driver interpretation module, and an actuation module. The pedal torque determination module determines a zero pedal torque based on a desired engine torque at a zero accelerator pedal position and a minimum torque limit for an engine system. The driver interpretation module determines a driver pedal torque based on the zero pedal torque and an accelerator pedal position. The actuation module controls at least one of a throttle area, spark timing, and a fuel command based on the driver pedal torque.

Method to include fast torque actuators in the driver pedal scaling for conventional powertrains

An engine control system comprises a driver axle torque request module (DATRM) and a driver axle torque security module (DATSM). The DATRM determines a pedal torque request based on minimum and maximum scaling torques and a torque scalar. The DATRM determines a raw driver torque request. The DATRM selectively shapes raw driver torque request into a final driver torque request. The DATRM converts the final driver torque request into a first axle torque request. The DATSM selectively diagnoses a fault in the first axle torque request based on a minimum engine torque, the minimum scaling torque, a first comparison of the final driver torque request and the redundant final driver torque request, and a second comparison of the first axle torque request and a redundant axle torque request.

Securing driver requested torque

A vehicle speed module includes a speed arbitration module that receives at least two of a wheel speed, a transmission output speed (TOS), and an electric motor speed (EMS), and that determines a vehicle speed based on a comparison of the at least two of the wheel speed, the TOS, and the EMS. A speed diagnostic module selectively diagnoses a fault in one of a wheel speed sensor, a TOS sensor, and an EMS sensor based on the comparison.

Securing and diagnosing the vehicle speed input and direction for torque control systems

A vehicle diagnostics clearing system that detects a clear diagnostic faults flag and clears diagnostic faults from a control module includes a clear diagnostic faults flag monitoring module and a clear diagnostic faults module. The clear diagnostic faults flag monitoring module periodically monitors the clear diagnostic faults flag in the control module. When the clear diagnostic faults flag monitoring module detects that the clear diagnostic faults flag is set, the clear diagnostic faults module clears the diagnostic faults from the control module for a predetermined period.

Diagnostic fault clearing system

Growing community of inventors

Ann Arbor, MI, United States of America

Ronald W Van Diepen