Jenesis International Incorporated

Other

Winvic Sales Inc.

Nii Northern International Inc.

Roger Don Bentley

Kim Irwin McCavit

Bradford Brian Jensen

Kim Irvin McCavit

Robert H Ashton

Mark Adam Goldy

Mccavit Kim I I

Kim I Mccavit

A decorative ornament powered by a vertical axis wind turbine. The turbine includes blades that rotate about a centrally located vertical shaft. An LED illuminated globe is centrally located within the rotating blades and is secured atop the shaft. An alternator is located below the globe and is coupled to the rotating blades. The blades are shaped having a leading cupped section joined to a lagging airfoil section. The leading cup section is defined by a cup radius r and the lagging airfoil section is defined by an airfoil chord length CL. The cup radius r and chord length CL both decrease towards the terminal bottom and top ends of the blade. Also, the airfoil section is located a radial distance Cd from the vertical axis and the radial distance Cd decreases towards the terminal bottom and top ends of the blade.

Illuminated ornament powered by vertical axis wind turbine

A method of illuminating an ornament having a light emitting source, a battery power source and a control circuit energizing the light source at desired intensities over desired durations of time. Light from the right source travels through an ornament wall. The method repeats the steps of increasing the light intensity from a low to a high intensity during a rise time period; decreasing the light intensity to a low intensity during a fall time period which is not less than the rise time period; and, maintaining the low intensity of light during a remaining time period which is not less than the combined rise and fall time periods. The low intensity of light is less than one third the high intensity. The light intensity decreased and maintained briefly at zero intensity during an off time period between the remaining and rise time periods in an imperceptible manner.

Method of illuminating ornament

An illuminated ornament having an electronics assembly including a battery holder, a cap, a light emitting source and a control circuit is inserted through a hole axially into the ornament enclosure thereby locating the light source at a distance from the enclosure wall. The enclosure wall allow light to travel therethrough. A diffusing and reflecting cap which is preferably conical shaped converging towards a disk shaped end wall surrounds the light source and both allows light to travel therethrough and reflects light behind the light source to the enclosure wall. The battery holder is permanently attached to the assembly cap and the electronics assembly is removable from the enclosure in one piece. The assembly cap closes the hole. The differential pressure between the inside and outside of the enclosure is relieved preventing air and water entry through the assembly cap to enclosure interface.

Illuminated ornament

An optical sensor controlled lighting system comprises an ambient light sensor responsive to ambient light levels for generating an output signal proportional to the ambient light level. A light source having on and off states is controlled by circuit elements providing for developing a rate of change for the output signal and further providing for, responsive to the rate of change, selectively switching the light source between on and off states based on characteristics of the rate of change.

Light level and light level rate of change sensor

Bottle

A decorative, imitation candle effectively simulates a lighted wick in a darkened environment by location of a light source at the tip of an imitation wick. The light source is provided by an LED located at the tip of the wick for direct viewing in order to obtain maximum brightness and high contrast to an observer in a darkened environment. The light source and its support structure are incorporated into the imitation wick so that they do not detract from the imitation candle's realism when the imitation candle is viewed from the side or from above under higher ambient lighting.

Imitation candle with simulated lighted wick using external light source

A decorative, imitation candle includes a simulated wick which generates the appearance of an open flame in a darkened environment. A light pipe is located at the expected location of the wick. The exposed end of the light pipe has a tip which produces a point like a light source with a glare effect to darkness accommodated eyes when the device is illuminated. The glare is interpreted as an open flame without the need for a flame shaped terminating structure which is visible when the imitation candle is unlit.

Imitation candle with simulated lighted wick

A decorative lantern evocative of enclosing a candle or other open flame type light source includes an imitation candle and a super bright light emitting diode hidden with the lantern to illuminate the imitation candle from outside. A wick having a polished tip produces a hot spot of reflected light to heighten the illusion of an open flame being present.

Lantern with imitation flame source

Battery powered LEDs operated at a small fraction of their rated capacity to provide a level of illumination useful as a marker for darkness adjusted vision. Long battery life is achieved using super bright, broad spectrum LEDs.

Marker lights for wireless doorbell transmitters and other devices

An imitation candle is made from a translucent material having light transmissive properties similar to paraffin. The imitation candle is shaped to appear reduced by burning. An LED, or similar high intensity light source, is set in a cavity within the imitation candle. The LED preferably produces amber light to better resemble the color of candle light. The imitation candle diffuses the light emitted from the LED to create a warm, natural looking glow. Light emission levels from the LED are varied in a pseudo-random manner to simulate the flicker of candle light.

Growing community of inventors

Coloma, MI, United States of America

Roger Don Bentley