The Singer Company

Robert S Prill

Ronald Y Paradise

James W Lang

Peter J Tufano

A memory access system for a computer is improved by combining look ahead techniques with a partitioned memory. A parallel system operating in reciprocal fashion accesses from one portion while the other portion is generating the next predicted address. The system can also be adapted for use with virtual addressing.

Look ahead memory interface

A stand-alone digital processor based system includes a five-output state digital filter provided with magnitude and time data relative to a received TACAN signal. Threshold detection is provided for validating the received signal magnitude. The filter outputs produce phase signals which are combined in the digital processor, in accordance with an algorithm, to generate bearing data. The bearing data is stored and scaled prior to updating a display.

Digital TACAN processor

A solid state synchro torque receiver driver that uses unfiltered AC as the power source and push-pull regulating transistors operating in the linear mode to drive the torque receiver stator loads. A feedback amplifier compares the push-pull outputted AC signal against an inputted AC data reference (i.e. the desired stator excitation amplitude) and thus closes the loop forcing the output to follow the input. The synchro torque receiver operates in a closed loop and thus has realizable potential of near infinite resolution and high accuracy.

Solid state synchro torque receiver driver

High accuracy distance measurements are achieved with a low accuracy Tacan set by utilizing signals available within the Tacan set at a point of sufficient accuracy to provide accurate distance measurements to be made and thus upgrade an en-route navigation aid to higher accuracy for use in a precision landing system.

Updating an en-route Tacan navigation system to a precision landing aid

A signal conditioning circuit for a fixed rise time, variable amplitude receiving system (TACAN) that digitizes the time of arrival and samples the pulse amplitude at the receiver's last intermediate frequency (IF) stage before video detection. The time of arrival measurement is performed by counting a fixed number of successive threshold crossings of the IF carrier, utilizing a pair of comparators having two inputs each. One input of each comparator is coupled to the IF stage. The other input of each comparator is coupled to a point of reference potential, one comparator being referenced to ground and the other being coupled to a small positive threshold voltage level. The output of the grounded comparator is delayed, and the delayed output is used as a clock signal to the remaining circuitry. The output of the threshold comparator provides data pulses, one data pulse being generated each time that the IF signal goes above the threshold value. The data pulses, along with the clock pulses, are applied to an up down shift register which acts as a digital flywheel. The output of the digital fly-wheel enables and disables a counter. Two signal conditioning circuits are described, one which extracts time information, and one which extracts amplitude information from a fixed rise time, pulse-amplitude modulated carrier as is found in a typical TACAN receiver at the last intermediate frequency (IF) stage. The time of arrival of the leading edge 50% voltage point is determined in real time with virtually zero delay, and therefore does not rely on conventional approaches which must first wait until the full unknown amplitude of the pulse is determined before a 50% detector is enabled. The technique is based on the fact that there are a fixed number of cycles of IF carrier under the leading edge of the pulse regardless of its amplitude and that therefore the 50% voltage point is determined by counting in an electronic counter a fixed number of 'consecutive' cycles that exceed a pre-determined noise threshold as determined by a comparator set at that threshold. The technique operates on the signal one stage before conventional video detection. Erroneous false alarm and false dismissal threshold crossings are rejected by a digital up-down shift register which acts as a fly-wheel. The peak amplitude of the IF pulse-amplitude modulated carrier is detected, sampled, amplified, and buffered in one efficient circuit. The detection function is performed by charging a capacitor, which is isolated from the raw IF by a differential amplifier stage, up to a voltage proportional to each successive carrier cycle peak by a closed loop means. Since the capacitor can only charge in one direction, it charges up to a voltage proportional to the most positive peak of the pulse-amplitude modulated carrier, with a fixed amount of rate limiting for noise immunity. Two logic signals, a Track/Hold command and a Dump command are used to respectively hold the peak amplitude for subsequent analog to digital conversion and digital signal processing, and to reset the detector prior to encoding another pulse.

Growing community of inventors

Parsippany, NJ, United States of America

Robert S Prill