Ii-Vi Delaware, Inc.

Finisar Corporation

Syntune Ab

Finisar Sweden Ab

Robert Lewén

Andrei Kaikkonen

David Adams

Jan-Olof Wesström

Urban Eriksson

Nicolae Chitica

Christopher Daunt

Filip Öhman

Martin Zirngibl

Marek Grzegorz Chacinski

Osamu Mizuhara

Simon Chen

Efthymios Rouvalis

An electro-absorption modulator (EAM) is configured to include an on-chip AC ground plane that is used to terminate the high frequency RF input signal within the chip itself. This on-chip ground termination of the modulation input signal improves the frequency response of the EAM, which is an important feature when the EAM needs to support data rates in excess of 50 Gbd. By virtue of using an on-chip ground for the very high frequency signal content, it is possible to use less expensive off-chip components to address the lower frequency range of the data signal (i.e., for frequencies less than about 1 GHz).

Broadband electro-absorption optical modulator using on-chip RF input signal termination

An optical communication device may include a driver component, arranged to achieve a driving voltage, and a modulator component, including a laser or arranged to receive light from a laser. The modulator component may be arranged to achieve a modulated light signal modulated based on the driving voltage. The device may include a transmission line arranged to transfer the driving voltage between the driver component and the modulator component. The transmission line may not impedance matched to the driver component, the transmission line may have an impedance which is at least 20% lower than an output impedance of the driver component, and the transmission line may be impedance matched with respect to signal reflections to the modulator component.

Optical communication device

An optical interference modulator comprises a main input, a main output, an optical splitter connected to the main input, first and second MMI couplers, each with a first primary-end access port connected to the splitter; a second primary-end access port connected to the main output; a first secondary-end access port connected to a respective primary waveguide; and a second secondary-end access port connected to a respective secondary waveguide. A light reflector is arranged to reflect light incident from said primary and secondary waveguides back into the same respective waveguide such that light travelling through the respective waveguide from the respective secondary-end access port, after reflection, travels back to the same secondary-end access port. For the MMI couplers, at least one of the respective primary and secondary waveguides comprises a respective light phase modulating device arranged to modulate the phase of light travelling along the corresponding waveguide in either direction.

Optical device

An electro-optical modulator includes a substrate comprising a first Mach-Zehnder modulator comprising a first waveguide and a second waveguide and a second Mach-Zehnder modulator comprising a first waveguide and a second waveguide. A first positive signal electrode is positioned on the substrate over the first waveguide of the first Mach-Zehnder modulator and a first negative signal electrode is positioned on the substrate over the second waveguide of the first Mach-Zehnder modulator. The first positive signal electrode and the first negative signal electrode are connected to a first differential signal input. A second positive signal electrode is positioned on the substrate over the first waveguide of the second Mach-Zehnder modulator and a second negative signal electrode positioned on the substrate over the second waveguide of the second Mach-Zehnder modulator. The second positive signal electrode and the second negative signal electrode are connected to a second differential signal input. A first ground electrode is positioned on the substrate between the first and second Mach-Zehnder modulators connected to ground potential. A second ground electrode is connected to ground potential and positioned on the substrate adjacent to the first Mach-Zehnder modulator such that the first positive signal electrode and the first negative signal electrode are between the second ground electrode and the first ground electrode. A third ground electrode is connected to ground potential and positioned on the substrate adjacent to the second Mach-Zehnder modulator such that the second positive signal electrode and the second negative signal electrode are between the third ground electrode and the first ground electrode. A plurality of first electrical connectors connect the first ground electrode to the second ground electrode and a plurality of second electrical connectors connect the first ground electrode to the third ground electrode. A spacing between at least two of the plurality of first electrical connectors is chosen to achieve a desired cross talk between an optical signal generated by the first Mach-Zehnder modulator and an optical signal generated by the second Mach-Zehnder modulator.

Reduced-cross-talk coherent optical transmitter

Method for calibrating and tuning a part wise monotonically, continuously tunable semiconductor laser having a phase section and a first Bragg reflector section, through which sections a phase current and a first reflector current, respectively, are applied, which laser is not actively cooled, includes a) a calibration step, including obtaining at least two tuning lines along which tuning lines all combinations of phase and Bragg currents are stable operating points, identifying at least one reference stable operating point along a first one of the identified tuning lines at which operating point the laser emits light at a certain reference frequency, and storing at least one reference stable operating point; and b) a subsequent tuning step, during which the output frequency of the laser in relation to the reference frequency is controlled to a desired output frequency by translating the operating point of the laser along the first tuning line.

Method for calibrating a tunable laser

Method for calibrating a tunable semiconductor laser having a phase section and a first Bragg reflector section, through which sections a phase current and a first reflector current, respectively, is applied, includes: a) selecting a phase current; b) identifying a range of reflector currents that achieves emission of light from the laser within a desired frequency band; c) scanning the reflector current(s) over the range of reflector currents, for each of at least two different phase currents, and reading the relative output power of the laser for each point scanned; d) identifying one stable operating point; e) identifying and storing one stable, continuous tuning line as constructed by interpolating; f) calibrating the laser frequency and observing a fed back signal from a target for the light emitted from the laser; g) measuring the temperature of the laser; and h) storing temperature and one operating point along the tuning line.

The present invention relates to an optical modulator, divided into at least two active segments separated by at least one passive segment. The modulator comprises: an optical waveguide with an optical group index nhaving an optical signal propagating at an optical velocity v, and a microwave transmission line with an electrical propagation index n, having an electrical signal propagating at an electrical velocity V. The electrical propagation index nof the unloaded microwave transmission line is lower than the optical group index nof the optical waveguide. The loading and length of the microwave transmission line are adjusted for a specific Bloch impedance and electrical velocity v. The invention also relates to a method for adapting the impedance of an optical modulator.

Growing community of inventors

Tyresö, Sweden

Robert Lewén