The Watt Stopper, Inc.

Other

Bayview Technology Group, Incorporated

Power Innovations, Ltd.

Bayview Ventures, Inc.

Richard R Billig

Alexandre Debernard

Bertrand Debever

David J Schanin

Steven B Carlson

Thomas L Grey

Location-Based Addressing (LBA) is a method of controlling and commissioning networked lighting devices. The lighting devices communicate over a wireless network using radio frequency communication protocols. The lighting devices are commissioned or grouped based on their 5 respective locations in a building floor plan or a building architecture. The lighting devices are commissioned to respond to radio frequency communications that correspond to their respective locations. This imposed location-based architecture reduces the amount of transmitted data required to control the lighting devices and, thus, reduces the radio bandwidth required to control the lighting devices. In other words, controlling devices 'multicast' instructions and controlled devices 'listen' for instructions and act only upon instructions that correspond to their respective location. Hand shaking or two-way communication between the controlling devices and the controlled devices is not required.

Location-based addressing lighting and environmental control system, device and method

Location based addressing lighting and environmental control system, device and method

A multi-sensor lighting control system includes at least two light sensors. Each sensor gathers light from different sources, by comparing and contrasting the output signals from the two sensors, the controller can automate many lighting control and commissioning processes leading to easier, simpler installations and maintenance and happier customers, and removing the need for special tools. Applying automated closed loop lamp warm-up techniques, the daylight ratio and the maximum electric light contribution can be learned automatically by the system. A multi-sensor lighting control system may also provide intermediate zones of lighting control between adjacent task areas with different lighting requirements.

Method and apparatus for multiple sensor lighting control systems for daylight harvesting

Location-Based Addressing (LBA) is a method of controlling and commissioning networked lighting devices. The lighting devices communicate over a wireless network using radio frequency communication protocols. The lighting devices are commissioned or grouped based on their respective locations in a building floor plan or a building architecture. The lighting devices are commissioned to respond to radio frequency communications that correspond to their respective locations. This imposed location-based architecture reduces the amount of transmitted data required to control the lighting devices and, thus, reduces the radio bandwidth required to control the lighting devices. In other words, controlling devices 'multicast' instructions and controlled devices 'listen' for instructions and act only upon instructions that correspond to their respective location. Hand shaking or two-way communication between the controlling devices and the controlled devices is not required.

A phase-controlled power delivery system for a load such as an incandescent lamp controls the rate of transition of an AC power waveform as a function of switch temperature or other heat-related parameter to provide for time-varying optimization of a tradeoff between heat and noise.

Transition-rate control for phase-controlled AC power delivery system

A spread-spectrum power converter uses an inter-cycle duty-cycle error compensation to achieve a combination of high-precision tracking of a target average duty cycle and a favorable noise signature. The pulse train consists of a series of cycles having cycle durations of a positive integer of clock cycles, pulse durations of a whole number of clock cycles, and duty cycles corresponding to a ratio of pulse durations over cycle durations. The pulse durations are selected at least in part as functions of a target average duty cycle, the respective cycle durations, and a ripple (or other) error from other cycles in the train. The cycle durations can also be in part a function of the target average duty cycle so that the duty cycle errors can be minimized.

Spread spectrum power converter with duty-cycle error compensation

A thyristor-based forward phase control (FPC) system for controlling the power delivered to a load from an AC power source employs a short-circuit test cycle to protect the thyristor from damage. Upon activation of the FPC system, the thyristor is triggered at a phase less than one-twelfth cycle before a zero crossing so that, if there is a short, the resulting peak current will be insufficient to damage the thyristor but will exceed a predetermined threshold current corresponding to a repetitive overload current. If during the test cycle, the threshold current value is crossed, the FPC system does not trigger the thyristor again and does indicate that a short exists. The threshold current value is selected to correspond to the thyristor's steady-state load rating. If it is exceeded during normal (including warm-up and request-based) operation, steps can be taken to address an overload condition. Accordingly, the same circuitry used for general overload protection can be used as well for short-circuit protection.

Short-circuit protection for forward-phase-control AC power controller

A branch circuit includes an branch breaker, a master outlet, and two slave outlets in series with the master outlet. The master outlet is the closest of the outlets to the circuit breaker. It includes a power sensor, the output of which is graphically displayed on a multi-segment LED display visible from the front of the outlet. The power sensor output is also supplied to displays at the slave outlets so that the power measured at master outlet is indicated at all outlets. This allows the available power capacity for the branch circuit to be appropriately indicated at all outlets on the circuit. The design can be implemented inexpensively enough that it is economical to employ the invention at every outlet in a building.

Load monitoring electrical outlet system

A power conservation system (PCS) includes a data handler, a controller and a power switch. The data handler is located between a host network and a network printer, while the power switch is between an AC power source and the printer's power input. The PCS can thus shut down the printer during periods when no data is being sent to the printer. The PCS monitors data to and from the printer, allowing it to track the printer's state and to capture its network identification. State tracking permits the PCS to emulate the printer when it is down and when it is booting. Additionally, the information stored in a state memory of the data handler can permit the printer's last ready state to be reconstructed after it turns on and boots to a ready state. In some cases, the data handler can answer network requests without turning on the printer. Thus, the PCS provides for effective power conservation while remaining invisible to a user.

Power-conservation system for computer peripherals

A phase-controlled power modulation system switches modes in response to circuit-threatening conditions to avert the necessity of a shutdown. Normal operation is in reverse phase control (RPC) mode. When an inductive load sensor detects the presence an inductive load, the system switches to a forward phase control (FPC) mode (FPC) to minimize voltage spikes that would otherwise result from the load's opposition to voltage transitions. When an overcurrent sensor detects an overcurrent, the system switches into an asymmetric hybrid mode (AHPC) to maximize delivered power while remaining within switch current handling capacity. In AHPC mode, an RPC component of a half-cycle waveform is cut off at the current limit, while an FPC component of the same half-cycle waveform is triggered after the source voltage drops to a confidence threshold below the current limit to ensure that current limiting is not triggered again during the same half-cycle. In response to excessive temperature, a short transition mode is entered to reduce the heat generated at the switches until the temperature abates.

Growing community of inventors

Los Gatos, CA, United States of America

Richard R Billig