Powerwave Technologies, Inc.

Other

Aethercomm, Inc.

Richard D Posner

Do B Shin

Kwang Kim

Charles R Gentzler

Wayne Roberts

Gregory French

Stefan Klein

Bill Vassilakis

Ray K Butler

Ross James Wilkinson

Richard H Chesarek

Sandip Patel

William Brian Camp

Michael Scott Weeks

Thuan Tran

Walter Richard DeMore

Described herein are methods and system for providing digital non-linear loop control. In one embodiment, system with digital non-linear loop control comprises a parameter control circuit configured to modify a signal based on a control signal, a processing circuit configured to process the signal, and a parameter measurement circuit configured to measure a parameter value of the signal. The system also comprises a digital non-linear control circuit configured to compare the measured parameter value with a desired parameter value, to determine a control signal value based on the comparison using a lookup table (LUT) that characterizes a non-linear control response of the system, and to output the control signal to the parameter control circuit based on the determined control signal value.

Method and apparatus for a digital non-linear loop control circuit

A control system for a linear feed-forward amplifier, using the ratio of measured spurious energy. Measuring receivers are coupled to two monitoring points to measure the spurious energy content in the error signal and at the main output of a feed-forward amplifier. The control system measures the ratio of these detected spurious, and uses this to optimize the settings of the second loop distortion cancellation. With the addition of an extra monitoring point, the same technique may also be used to control an adaptive predistorter prior to the main amplifier.

Spurious ratio control circuit for use with feed-forward linear amplifiers

An RF power amplifier with amplifier stage failure detection comprises an amplifier input for receiving an RF signal to be amplified, an amplifier output for outputting an amplified RF signal, a plurality of separate amplifier stages coupled between the amplifier input and amplifier output so as to cumulatively provide a desired amplifier gain to the input RF signal, and means for detecting amplifier stage failure by providing a pilot tone separately to the amplifier stages based on a separate timing for each stage and detecting pilot tones output from the stages based on the timing.

Feed forward amplifier with amplifier stage failure detection using pilot tones

An RF power amplifier with amplifier stage failure detection comprises an amplifier input for receiving an RF signal to be amplified, an amplifier output for outputting an amplified RF signal, a plurality of separate amplifier stages coupled between the amplifier input and amplifier output so as to cumulatively provide a desired amplifier gain to the input RF signal, and means for detecting amplifier stage failure by providing a pilot tone to the amplifier stages, duty cycling the amplifier stages based on a separate timing for each stage and detecting the pilot tone output from the stages based on the timing.

The invention relates to a low cost feed forward RF power amplifier arrangement for amplifying an RF input signal using a main power amplifier operating as a class A/B amplifier. The method and apparatus modify the input signal to the main amplifier to compensate for the distortion added by the main power amplifier. The circuit provides for injecting a delayed version of the input signal, through a fixed gain-phase circuity, at a point whereby the resulting signal is amplified by the error amplifier of the second loop. A digitally controlled processor iteratively modifies various phase and gain controls to adjust the output of the amplifier. Different gain and phase control lines are iteratively updated at different rates.

Low cost, pilotless, feed forward compensation for a power amplifier

An apparatus for either combining a plurality of high frequency RF signal inputs or splitting a single RF frequency input into a plurality of RF signal outputs employs a switchable combining/splitting section and a switchable matching section. The switchable combining/splitting section operates to either combine the RF signal inputs to a common summed output or to take a matched input and to split it into a plurality of outputs. The matching section operates to switchably match the impedance presented by the combining/splitting section to achieve a minimum or zero insertion loss through the apparatus.

Switchable combiner/splitter

Systems and methods are taught whereby amplification of narrowband signals may be accomplished by linear power amplifiers requiring the presence of a communicated broadband signal in order to make internal adjustments necessary for linear operation. A preferred embodiment is described utilizing an input of a distributed amplifier assembly unused by the signals of interest in order to inject an emulated CDMA tone operable as a pilot tone for use by the linear power amplifiers.

System and method providing amplification of narrow band signals with multi-channel amplifiers

A method and apparatus reduce the out-of-band frequency components of an RF amplified signal, preferably a CDMA signal, which has a carrier frequency which is not known in advance. The apparatus and method feature locating the frequency of the incoming signal by examining an RF output signal having both in-band frequency components and out-of-band frequency components. Typically the output signal is generated using a high-power, Class A/B amplifier. Once the frequency of the carrier has been determined, the out-of-band components are used to generate control signals which, in, for example, a feedback or feedforward circuitry, reduce the energy of the out-of-band signals and thereby provide a more linear amplifier transfer function.

Amplification system having mask detection

A method and apparatus for reducing out-of-band frequency components of an RF amplified input signal, the amplified signal having both in-band frequency components and out-of-band frequency components, employ a feedforward network in which a microprocessor can sweep a frequency generator output connected to a mixer, the other input of the mixer being the amplified output, to find the carrier frequency of the input signal, and thereafter modify or control the feedforward circuit to reduce out-of-band frequency component energies in a particular manner. For example, gain and phase of a variable gain-phase network in a feedforward circuit structure can be modified for reducing the out-of-band frequency component energy.

Feedforward amplification system having mask detection compensation

A method and apparatus for reducing out-of-band frequency components of an RF signal having a carrier frequency which is not known in advance employ a control signal to vary adjustable bias parameters of the circuit. In particular embodiments, the RF signal is generated from a MOSFET power amplifier, which introduces distortion components into its output signal. Bias parameters of the MOSFET amplifier can be varied to reduce out-of-band frequency components, that is, out-of-band distortion. In addition, other elements of the network can be controlled by varying bias parameters, for example, a predistorter.

Growing community of inventors

Woodland Hills, CA, United States of America

Richard D Posner