Hon Hai Precision Industry Co., Ltd.

Hong-fu Jin Precision Industry (shenzhen) Co., Ltd.

Scienbizip Consulting(shenzhen)co., Ltd.

Shenzhen Treasure City Technology Co., Ltd.

Ping-Chuan Deng

Zheng-Heng Sun

An-Gang Liang

Han-Bing Zhang

Lei Liu

Li-Ren Fu

Jun-Hui Wang

Ai-Ling He

Ming-Yu Liu

Shu-Ni Yi

Lin Du

Kun Li

Jun He

Fei Teng

Wan-Li Ning

Yu Han

He Feng

Xia-Bing Gao

A heat dissipation simulator of a component on a printed circuit board (PCB) includes a simulation board and a simulated heat source. The simulation board includes an iron layer and a plastic layer. The simulated heat source includes a simulation chip, a thermal, and a heat sink. The simulation chip, the thermal piece, and the heat sink are mounted on the simulation board in that order. The heat dissipation simulator replaces a sample of the PCB with the component for simulating working states of the component on the PCB.

Heat dissipation simulator

A fan device includes a board defining an opening and a fan assembly pivotably received in the opening. The fan assembly includes a fan and a frame receiving the fan. The frame includes a top wall, a bottom wall, and two sidewalls. A front plate extends down and diagonally forward from a front side of the bottom wall. A resilient limiting member is formed on one of the sidewalls. When a bottom of the fan assembly is pivoted rearward to make the fan assembly slanting relative to the board, the front plate is abutted a front side of the board, and the limiting member is abutted a rear side of the board.

Fan device

A holding device includes a loading frame and two mounting plates. The loading frame includes a base portion for loading an HDD and a pair of sidewalls perpendicularly extending from the base portion. The sidewalls are parallel to each other. Each sidewall includes two sliding ribs substantially perpendicularly extending from a surface thereof away from the other sidewall. The two mounting plates are opposite to each other. Each mounting plate includes two guiding rails substantially perpendicularly extending from a surface thereof toward the other mounting plate. The two sliding ribs of each sidewall are configured to be slid into the two guiding rails of a corresponding mounting plate.

Holding device for hard disk drive

A disk on module device includes a serial advanced technology attachment (SATA) connector connected to a SATA interface of a motherboard, a universal serial bus (USB) connector connected to a USB interface of the motherboard, a power unit, a control chip, and a number of storage chips. The power unit is connected to a power pin of the USB connector, to receive electrical power from the motherboard through the USB connector and converts the received voltage to make it suitable for the control chip and the storage chips. The control chip is connected to the SATA connector and the storage chips, to receive a control signal from the motherboard through the SATA connector and control the storage chips to store data.

Disk on module device

A male universal serial bus (USB) connector includes a connection terminal and a locking piece. The locking piece includes a mounting piece fixed to a top wall of the connection terminal, an operation piece, and a connecting piece connected between the operation piece and the mounting piece. A wedge extends on the mounting piece and can be engaged in a female USB connector to prevent the male USB connector from disengaging from the female USB connector.

Connector and connector assembly

A connector assembly includes a connector and two screws. The connector includes a main body, a cable connected to a rear side of the main body, and a connection portion protruding from a front side of the main body. Two threaded holes are defined in opposite ends of the main body, respectively. Two resilient fixing portions protrude from the rear side of the main body. A through hole is defined in each of the fixing portions. The screws are detachably received into the corresponding through holes of the fixing portions, and operable to mount the connector to an object by extending through the threaded holes to engage with the object.

Connector assembly

A mounting apparatus for mounting a memory card includes a socket, a locking member attached to one end of the socket, and an operation member pivotably attached to the locking member. The operation member is used for operating the locking member to lock or release the memory card.

Mounting apparatus for memory card

A mounting apparatus for mounting a memory card includes a socket, a locking member attached to one end of the socket, and an operation member movably attached to the locking member. The operation member is used for operating the locking member to lock or release the memory card.

Growing community of inventors

Shenzhen, China

Ping-Chuan Deng