Enertechnix, Inc.

Peter C Ariessohn

Igor V Novosselov

Evan D Dengler

George Kychakoff

Michelle Hickner

Richard E Hogle

Apparatus and methods for selectively separating a volatile constituent of a particle from a gas stream for analysis. Particles are separated from bulk flow by inertia and impacted in a cavity containing a small but stable vortex or eddy. Heat is applied to volatilize constituents of the particles. The gas entrained within the vortex, which exchanges only slowly with the bulk flow, is withdrawn for analysis. In this way, a high volume flow containing particles of interest is reduced to a low volume flow containing a vapor concentrate. Advantageously, the apparatus may be operated at very low pressure drops in fully continuous, semi-continuous or batch mode according to the requirements of the downstream analytical unit. The apparatus finds use in active surveillance, such as in use of aerosols to detect explosives or chemical residues on persons, vehicles or luggage in real time.

Trapped vortex particle-to-vapor converter

An imaging system with the ability to produce clear images of deposits inside operating high temperature process equipment such as kraft recovery boilers and power utility boilers uses a terahertz/mm-wave imaging system. This system allows direct inspection capability and the ability to directly measure deposit thickness on tubes and other interior surfaces at all locations within the boiler and precipitator. Terahertz and mm-wave imaging systems employ active imaging in which a beam of terahertz or mm-wave radiation generated within the imaging system is used to illuminate a region of the scene under investigation. The reflected radiation is collected by a lens or mirror system and focused onto a detector that converts the collected radiation into an electrical signal. Both the illuminating beam and the receiving optics are scanned across the scene in a raster fashion to produce a time-varying signal that is converted into an image of the scene.

Terahertz imaging

Devices, apparatus and methods are disclosed for non-contact pneumatic sampling and sampling of surfaces, persons, articles of clothing, buildings, furnishings, vehicles, baggage, packages, mail, and the like, for contaminating aerosols indicative of a hazard or a benefit, where the contaminating aerosols are chemical, radiological, biological, toxic, or infectious in character. In a first device, a central orifice for pulling a suction gas stream is surrounded by a peripheral array of convergingly-directed gas jets, forming a virtual sampling chamber. The gas jets are configured to deliver millisecond pneumatic pulses that erode particles from solid surfaces at a distance. In another aspect of the invention, a suction gas stream is split using an air-to-air concentrator so that a particle-enriched gas flow is directed to a particle trap and any particles immobilized in the particle trap (including any adsorbed vapors associated with the particles) are selectively analyzed to detect trace residues associated with explosives.

Particle interrogation devices and methods

An apparatus or device for collecting aerosol particles from a gas stream, having a collector body enclosing a collector channel, a particle trap in the collector channel, and an injection duct for injecting a discrete microdroplet of an elution reagent. The particle trap may be a centrifugal impactor, a bluff body impactor, or an electrostatic impactor. Aerosol particles are deposited on the surface during collection and are subsequently eluted with a microdroplet or a series of microdroplets as a concentrated liquid sample so that the sample can be analyzed in situ or conveyed to a detector for analysis. The collector serves as an aerosol-to-liquid conversion module as part of an apparatus for detecting and analyzing aerosol particles, and may be used in an integrated environmental threat assessment system, for example for characterization of aerosolized chemical and biological weapons, or for industrial or environmental monitoring.

Aerosol collection apparatus and methods

An aerosol sampling intake configured to exclude particles generally greater than 20 microns AD and capture particles of less than about 10 microns AD with high efficiency, independent of weather conditions, through which air is sampled by suction. The intake combines an omnidirectional horizontal segment with diffuser and elbow, the elbow transitioning flow to a vertical segment, the vertical segment with overhanging lip, the centrifugal impactor for self-cleaning operation, thus relieving the dual problems of re-entrainment of particles bouncing from the impactor surface and fouling by particles sticking to the impactor surface. The device is adapted for use on moving vehicles, for sampling at increased windspeeds, or for sampling in rain.

Omnidirectional aerosol sampling intake

Devices and methods are disclosed for non-contact pneumatic sampling of surfaces, persons, articles of clothing, buildings, furnishings, vehicles, baggage, packages, mail, and the like, for aerosols or vapor residues indicative of a hazard or a benefit, where the residues are chemical, radiological, biological, toxic, or infectious in character. A central orifice for pulling a vacuum is surrounded by an array of convergingly-directed gas jets, forming a 'virtual sampling chamber'. The gas jets are configured to deliver millisecond pneumatic pulses that erode particles and vapors from solid surfaces at a distance. A curtain wall flow encloses the sampling area during pulse retrieval.

A sensing system simultaneously obtains images and surface temperatures of processing tubes inside process heaters using an imaging sensor operating in the visible or infrared regions of the spectrum and capable of detecting visible or infrared radiation emitted or reflected from surfaces within the process heater, and of providing an image signal to a display or to an image processor. One or more single element infrared detectors viewing specific regions within the aforesaid image accurately measure the intensity of radiation emitted by surfaces within those specific regions so as to allow the temperature of the surfaces within those specific regions to be inferred.

Sensing system for obtaining images and surface temperatures

A skimmer device for concentrating an aerosol from a flowing gas stream, having an inlet with inlet aperture and inlet raceway, an outlet with virtual impact void and collector channel, and bulk flow divertors symmetrically disposed on either side of the long axis of flow, further characterized in that the downstream walls of the bulk flow divertors are concavedly curved and reverse the direction of bulk flow. In section, the four channels or passages of the 'skimmer' thus form a 'crossed tee' with concavedly contoured lateral arms curving back around. The lateral flow channels are for diverting the bulk flow into exhaust chimney spaces, and the chimney spaces are positioned proximate to the inlet element and anterior to the collection channel. In operation, the bulk flow streamlines are thereby folded more than 90 degrees away from the long axis of flow on the laterally disposed concave walls of the bulk flow channels. While counterintuitive, this was found using computational fluid dynamics (CFD) and experimentation to dramatically reduce wall separation and related instabilities and to improve particle recoveries. Large two-dimensional arrays of closely stacked inlet and skimmer elements are thus achieved by fitting the chimneys into spaces between parallel inlet elements. The interlinked problems of flow instability, manufacturability of arrays, and scale-up of chimney cross-sectional area to equalize pressure differentials in the bulk flow diverter exhaust ducts, particularly in two-dimensional arrays at high throughput, are uniquely solved with this geometry.

Skimmer for concentrating an aerosol

Respirable particles with diameters on the order of 0.05 to 10 microns entrained in an air stream, are concentrated in an aerodynamic lens (FIG.) for separation from the air steam. The entire structure is made by microfabrication techniques, such as silicon micro-machining which enables arrays of precisely aligned slit lenses to be made on a silicon chip. At a Reynolds number of 800, a slit 25 microns wide by 1 mm tall will pass a flow of only 0.28 liters per minute, but arrays of lenses (FIG.), stacked in parallel banks, multiplies the available flow rate. Placing a skimmer () at the exit of each silicon micro-machined lens in the assembly and connecting the skimmer channels in chimneys (), allows the bulk of the gas flow to be stripped off while allowing the concentrated particle stream to pass into a region of much lower flow rate, thereby producing a highly concentrated aerosol in the low velocity stream.

Growing community of inventors

Seattle, WA, United States of America

Peter C Ariessohn