Avery Dennison Corporation

Avery Dennison Retail Information Services, LLC

Ekc Technology Inc.

Peikang Liu

Scott Wayne Ferguson

Jason D Munn

Ian J Forster

Christine U Dang

Steven C Kennedy

Thomas Craig Weakley

David Puleston

David Nicholas Edwards

Samuel A Linder

James P Coleman

Yukihiko Sasaki

Ajay Virkar

Xiqiang Yang

Jaime Christopher Grunlan

Stephen Li

Andrew W Holman

Kourosh Kian

Dave N Edwards

Nazim Uddin

Composite materials with noble metal coated silver nanowires loaded into polymer are described. The composite materials may have resistivities of no more than about 100 Ohm-cm, or from about 100 Ohm-cm to about 1×10Ohm-cm depending on the amount of noble metal coated silver nanowires loaded into the polymer. The noble metal coated silver nanowires may be platinum coated silver nanowires. Metal particulates such as silver flakes or silver particles may be added to the composite materials in order to obtain desired properties. Composite precursor compositions and methods for preparing the composite materials are described.

Silver nanowire and noble-metal coated silver nanowire conductive polymer composites with low loading percolation conduction

Various methods for preparing and/or processing electrically conductive aluminum members such as used in electronic circuits and components are described. Also described are various sheet assemblies using patterned aluminum conductive elements as components of electric circuitry. The sheet assemblies can be used as backsheets for back contact photovoltaic cells or as antennas for RFID tags.

Sheet assembly with aluminum based electrodes

A radio frequency identification (RIFD) inlay includes an electrical connection between a chip and an antenna. The electrical connection includes conductive interposer leads and a capacitive connection. The capacitive connection may involve putting the antenna and the interposer leads into close proximity, with dielectric pads therebetween, to allow capacitive coupling between the antenna and the interposer leads. The dielectric pads may include a non-conductive adhesive and a high dielectric material, such as a titanium oxide. The connections provide a convenient, fast, and effective way to operatively couple antennas and interposers. The RFID inlay may be part of an RFID label or RFID tag.

RFID device and method of forming

A method of forming an electrically-conductive pattern includes selectively electroplating the top portions of a substrate that corresponds to the pattern, and separating the conductive pattern from the substrate. The electroplating may also include electrically connecting the conductive pattern to an electrical component. Conductive ink, such as ink including carbon particles, may be selectively placed on the conductive substrate to facilitate plating of the desired pattern and/or to facilitate separation of the pattern from the substrate. An example of a conductive pattern is an antenna for a radio-frequency identification (RFID) device such as a label or a tag. One example of an electrical component that may be electrically connected to the antenna, is an RFID strap or chip.

Conductive pattern and method of making

A radio frequency identification (RFID) device includes a conductive pattern, such as an antenna, on one side of a substrate, and a chip, such as part of a strap, electrically coupled to the conductive pattern, and either on an opposite side of the substrate or on the same side of the substrate as the antenna. A method of fabricating the RFID device may include crimping the strap onto the substrate, in contact with a seed layer, which is subsequently used in forming the antenna or other conductive pattern by plating. The seed layer may be a patterned conductive ink layer. Alternatively, the seed layer may be a layer of conductive material deposited on the substrate, such as by vacuum deposition. Parts of the deposited layer may be covered with a patterned mask in order to form the desired configuration of the conductive pattern.

RFID device and method of making

A radio frequency identification (RFID) inlay includes an electrical connection between a chip and an antenna. The electrical connection includes conductive interposer leads and a capacitive connection. The capacitive connection may involve putting the antenna and the interposer leads into close proximity, with dielectric pads therebetween, to allow capacitive coupling between the antenna and the interposer leads. The dielectric pads may include a non-conductive adhesive and a high dielectric material, such as a titanium oxide. The connections provide a convenient, fast, and effective way to operatively couple antennas and interposers. The RFID inlay may be part of an RFID lable or RFID tag.

Method of making RFID device

A radio frequency identification (RIFD) inlay includes an interposer that has a chip, and an antenna on an antenna substrate. The antenna substrate has a recess or hole, and the chip is at least partially in the recess or hole. By placing the chip or the interposer face down and at least partially in a recess or hole, thickness of the inlay may be reduced.

A device, such as a radio frequency identification (RFID) inlay structure for an RFID tag or label, includes a microstructure element, with leads coupling the microstructure element to other electrical or electronic components of the device. The leads may be electroless-plated leads, and may contact connectors of the microstructure element without the need for an intervening planarization layer.

Growing community of inventors

Claremont, CA, United States of America

Peikang Liu