Philips Electronics North America Corporation

U.S. Philips Corporation

Paulo P Caldeira

Rui Liu

Jinrong Qian

Antonius H Holtslag

Wen-Jian Gu

Gregory T DiVincenzo

William S Burdick

Daniel Kustera

Dhaval B Dalal

Joseph G Zahnen

Lawrence Bourdillon

A controller for supplying a switching signal to a switched mode power supply, includes a sinusoidal-like wave generator, and circuitry for selectively shifting a dc level in the sinusoidal-like wave whereby a duty cycle of the sinusoidal-like wave at a predetermined threshold level, corresponding to a turn-on level of a power switch in the switched mode power supply, is effectively controlled.

Low noise sinusoidal controller for pulse width modulated converters

A high frequency HID ballast includes an inverter for operating the HID lamp at high frequency and an arc instability controller which detects and adjusts the operating frequency of the inverter to avoid acoustic resonance of the discharge arc. The ballast ensures that the power delivered to the lamp remains substantially constant despite variations in the gain of the inverter which occur with changes in the operating frequency. Power control is accomplished by sensing lamp power and controlling a boost converter to vary the bus voltage feeding the inverter. The boost converter is also controlled during lamp ignition, when the load provided by the HID lamp is low, to clamp the bus voltage at a predetermined level. The ballast employs universal techniques suitable for operating HID lamps of different types, wattages and manufacturers despite the occurrence of acoustic resonance/arc instabilities among these lamps over a fairly broad frequency range.

Controller for a gas discharge lamp with variable inverter frequency and

Current in a line is measured by passing it through a coil, having at least one turn, linking a small high permeability core; passing a measuring current through a bucking winding around the same core; and controlling the measuring current to buck the magnetomotive force of the line current so that the core flux stays below the saturation level. The measuring current may flow through a precision resistor so that a voltage across the resistor is an accurate measure of the line current. The measuring current is obtained from a high frequency switching circuit which senses the change of flux in the core. In normal operation the circuit switches when the core flux has risen to a predetermined value, such as 60% or 80% of the saturation value. If drift or extreme transients cause the flux to reach the saturation level, a sensing and correction circuit re-establishes operation between the desired points.

Isolated current sensor for DC to high frequency applications

A converter for supplying various output voltages for a television receiver includes a multi-resonant circuit, including a resonant inductor, the leakage inductance of a flyback transformer, and a charging capacitor (including the parasitic capacitance of a switching transistor). This arrangement relaxes the slope of the voltages in the converter resulting in reduced radiated EMI. In addition, the values of the inductor and the capacitor are adjusted so that the switching transistor turns on at zero voltage and zero current so that the switching transistor is less stressed and the converter is capable of high frequency operation. Finally, the switching signals applied to the switching transistor are subjected to a filter-delay to lessen the slope of the signals thereby also resulting in a reduction in the EMI radiated from the driving circuit.

Low noise multi-output and multi-resonant flyback converter for

A forward converter for supplying various output voltages for a television receiver includes a multi-resonant circuit, including a resonant inductor, a charging capacitor, and the output capacitors across each secondary winding of an output transformer. This arrangement relaxes the slopes of the voltages in the converter resulting in reduced radiated EMI. In addition, the values of the inductor and the capacitors are adjusted so that a switching transistor in the forward converter turns on at zero voltage and zero current so that the switching transistor is less stressed and the converter is capable of high frequency operation. The secondary providing high voltage includes the series arrangement of two oppositely conducting diode branches, each branch including the series arrangement of a high voltage diode and a Schottky diode. Finally, the switching signals applied to the switching transistor are subjected to a filter-delay to lessen the slope of the signals thereby also resulting in a reduction in the EMI radiated from the driving circuit.

Growing community of inventors

Scarsdale, NY, United States of America

Paulo P Caldeira