Morton International, Inc.

Rohm and Haas Company

Other

Akzo Nobel Coatings International B.v.

Paul R Horinka

Andrew T Daly

Jeno Muthiah

Glenn D Correll

Joseph J Kozlowski

Richard P Haley

Martin J Korecky

Eugene P Reinheimer

Edward G Nicholl

Gregory R Mill

E Susanne Deibert

Grant E Schlegel

Diane K Pennington

Gerald T Werner, Jr

Karl R Wursthorn

Carryll A Seelig

Douglas S Richart

Gordon L Tullos

Douglas S Cinoman

Robert M Didrick

John R Petro

Michael G Favreau

Jeffrey B Farro

Todd M Bender

Jason Paul Breidenstein

Andres T Daly

Richard P Haly

A powder composition including a resin and from 5% to 70%, by weight based on powder composition weight, of a corrosion-inhibiting pigment, optionally including from 0% to 65%, by weight based on powder composition weight, zinc, the composition being substantially free from pigment providing a metallic effect is provided. The corrosion-inhibiting pigment may be present in amounts of up to 50%, by weight based on powder composition weight, for example, up to 35%. A method for coating a substrate with the powder composition and the coated substrate so formed are also provided.

Powder corrosion and chip-resistant coating

A method of providing a powder coating to MDF substrate panels wherein, by the differential treatment of the front and back surfaces of these panels, both surfaces can be coated at the same time and the effects of moisture and other volatile outgassing is controlled in such a way as to provide a blemish-free front facing surface with a minimal, but nonetheless acceptable, amount of blemishes on the opposite or back surface. Differential treatment is achieved by preparing each surface using different grades of sand-paper, applying different amounts of curing energy, whether infra-red or thermal, or by applying different thicknesses of coating to each surface.

Differential processing of powder coated substrates

Machine-profiled edges and corners and other surface discontinuities of heat sensitive workpieces such as wooden cabinet doors are uniformly covered by a coating powder applied electrostatically to the back side of the workpiece first, allowing the powder to wrap around the edges toward the front side, and then applying the coating powder electrostatically to the front side and fusing or fusing/curing the coating powder.

Process for coating cabinet doors

A process of forming coatings on substrates by applying a layer of curable materials in dry powder form and then melting and curing the material is improved by compressing the layer using a flexible confining membrane. Less material is required to provide equivalent barrier protection and surface finish. The process is particularly applicable to applying dry powder coatings on temperature sensitive substrates, such as medium density fiberboard, in press apparatus, such as a membrane press, which have not commercially used dry powder coating materials previously.

Powder coating involving compression of the coating during curing

An atomized fluid, such as a mist of water, is applied to a preheated substrate, such as wood, a wood product, paper, or ceramic just prior to or contemporaneously with electrostatically applying a coating powder to the substrate. The atomized fluid is absorbed or adsorbed by the substrate so as to enhance the charge-carrying capacity of the substrate to an extent necessary to promote efficient electrostatic application of the coating powder to the substrate.

Method of applying a coating powder to a substrate

In substrates, such as wood substrates, having sharp edges, corners and other surface discontinuities, in a front appearance surface, non-functional machining, such as formation of grooves, is performed on the rear non-appearance surface adjacent the surface discontinuities. Coating powder is applied, e.g., electrostatically, to the appearance surface of the substrate and the coating powder fused or fused and cured to form a continuous coating on the appearance surface of the substrate. The rear surface machining reduces cracking of the coating at the front surface discontinuities. In some cases, non-functional machining is distributed over the entire non-appearance surface of the work-piece to promote out-gassing of volatiles to the non-appearance surface, thereby eliminating out-gassing-caused defects in the coating formed on the appearance surface.

Method of powder coating a substrate

Wood is electrostatically coated with a thermosetting powder coating system in which a mixture of a self-curing epoxy resin and a catalyst therefore is extruded and a low temperature curing agent are both pulverized and the powders are blended with conventional additives to make a coating powder which is deposited on a wooden substrate and heated to cure. The mixture of resin and catalyst does not cure within the extruder but it is made to cure at low temperatures by the separate addition of the curing agent. A small amount of the low temperature curing agent, insufficient to cause substantial curing during extrusion may be used in place of the catalyst.

Two component powder coating system and method for coating wood therewith

An electrically chargeable dielectric coating powder and a triboelectric coating process for applying the powder to wood substrates are described. The coating powder is a mass of finely divided, heat fusible dielectric plastic material having an average particle size (Mv) of between 30 and 45 microns and a particle size distribution (all percents defined in weight percent) of:

Triboelectric coating powder and process for coating wood substrates

An electrically chargeable dielectric coating powder and a triboelectric coating process for applying the powder to substrates are described. The coating powder is a mass of finely divided, heat fusible dielectric plastic material having an average particle size (Mv) of between 30 and 45 microns and a particle size distribution (all percents defined in weight percent) of:

Triboelectric coating powder and process

Triboelectric coating powder and procees for coating wood substrates

Thermosetting powder coating compositions adapted to form a grainy textured finish on heat sensitive substrates, especially wood products, such as particle board, conductive particle board, and medium density fiber board, without damaging the substrates comprise an epoxy resin, particularly bisphenol A type epoxy resins having low viscosities, either a catalytic curing agent comprising an imidazole, a substituted imidazole, or adduct of an imidazole or substituted imidazole and an epoxy resin, or a curing agent comprising an adduct of a polyamine and an epoxy resin, or a combination of the catalytic curing agent and curing agent, a texturing agent, a flow control agent, optional extender, and optional pigment. The thermosetting powder coatings have a cure time/temperature ranging from about 30 seconds at about 350.degree. F. peak substrate temperature down to about 20 minutes at about 225.degree. F. peak substrate temperature which provides for either a rapid cure or low bake temperature to prevent excessive heat exposure to the heat sensitive substrate, resulting in substantially no physical or chemical degradation of the heat sensitive substrate during baking. The powder coatings are applied to heat sensitive substrates, especially wood products, through electrostatic spraying onto the substrate followed by heating to cure the textured finish uniformly on the surfaces and edges of the substrate. Electrostatic spraying is performed with a triboelectric or corona spray gun and heat curing is performed with a high intensity infrared oven, a convection oven, or combination. Coated heat sensitive substrates having continuous grainy textured finishes that are excellent for hiding substrate surface defects and later appearing scratches are obtained.

Textured epoxy powder coating compositions for wood substrates and

An electrical chargeable dielectric coating powder and a triboelectric coating process for applying the powder to substrates are described. The coating powder is a mass of finely divided, heat fusible dielectric plastic material having an average particle size (My) of between 30 and 45 microns and a particle size distribution (all percents defined in weight percent) of:

The use of cyclamic acid as a catalyst for the curing of hydroxyl-functional resins having a functionality greater than 2 provides a wrinkle finish. The hydroxy-function may be present in polyesters, epoxies, and acrylate or methacrylate resins, among others. The polyester resins which are able to provide such a finish have a hot plate melt flow of from about 20 mm to about 150 mm.

Growing community of inventors

Reading, PA, United States of America

Paul R Horinka