L3harris Technologies, Inc.

L3 Technologies, Inc.

Patrick L Newbold

Brent A Kenney

Matthew J Reimann

Philip M Hirz

Brian J Thorp

Thomas R Giallorenzi

Radivoje Zarubica

Jeffrey B Bench

Jason Wilden

Edwin J Hemphill

Marc Padilla

James E Hawker

Michael S Feeney

James E Peterson

Christopher S Heffernan

Brent Kenney

Bryan J Thorp

Indicating to a receiver node in a network that the receiver node should begin tracking signal to noise ratio (SNR) of a received signal for a new power and rate (PAR) interval for data sent from a transmitter node. A method includes determining that a new PAR interval is beginning. The method further includes adding an identifier to a data block. The identifier corresponds to the new PAR interval. The method further includes sending the data block from the transmitter node to the receiver node, where the receiver node will use the identifier to determine that a new tracking interval of SNR should be performed for the data block and subsequent data blocks having the identifier.

Deterministic power and rate control

Compensating for antenna gain losses due to attitude changes of a mobile local node in a network. A method includes at the local node, identifying an attitude change of the local node. As a result of identifying the attitude change of the local node, the method includes increasing a target SNR of forward data directed to one or more remote nodes by a boost value. As a result of identifying the attitude change of the local node, the method includes causing the remote node to adjust at least one of power or rate to compensate for the attitude change for subsequent reverse data sent from the remote node to the local node.

Proactive power and rate control algorithm for dynamic platforms in a mesh network

Joining subnets in mobile ad-hoc network (MANET) environment. A method includes, based on SNR, power and data rate information between a first gateway node for a first subnet and a second gateway node for a second subnet, determining a rate at which the first and the second subnets can connect if nodes in the first subnet reduce signal transmit rate to a predetermined level. The method further includes as a result of determining that the determined rate meets or exceeds a predetermined threshold, then joining the first and second subnets by joining the first and second subnets via the first and second gateway nodes and causing nodes in the first subnet to reduce signal transmit rate to the predetermined level.

Gateway link management between disjoint subnetworks in a CDMA MANET

Determining maximum transmit power by a local node. A method includes identifying one-hop neighbor nodes of the local node in the mesh network. One or more threshold maximum changes in interference caused by the local node increasing its transmit power for each of the one-hop neighbor nodes of the local node are identified. A plurality of power change values are identified. Each power change value in the plurality of power change values corresponds to a power change at the local node that would cause one of the threshold maximum changes in interference to occur at a corresponding one-hop neighbor node of the local node. A lowest power change value from among the plurality of power change values is identified. As a result, power transmitted by the local node is increased, while limiting an increase in power transmitted by the local node to no more than the lowest power change value.

Conscientious power and rate adaptation in a CDMA manet

Transmitting data in a mesh network. A method includes identifying points on a piecewise continuous surface. The piecewise continuous surface defines minimum threshold power values to maintain a predetermined signal-to-noise ratio at a predetermined bitrate for a transmitter node transmitting to one or more receiver nodes in the mesh network. Points of a constant total power surface are identified defining required ratios of transmitting power for transmitting sources of the transmitter node. One or more points on the piecewise continuous surface that intersect with the constant total power surface are identified. As a result, transmitting power levels for the transmitting sources of the transmitter node are identified. As a result, data is transmitted at or above transmitting power levels, using the transmitting sources.

Power and rate control algorithm for multi-antenna communication links in a mesh network

Transmitting a probe signal. A method includes transmitting a signal, having a predetermined total power, during a transmit cycle. The signal has a traffic channel transmitting user data and a probe channel to locate new nodes to add to the network. The transmit channel uses a first portion of the total power and the probe channel uses a second portion of the total power. The method further includes performing a probe cycle by lowering the power in the first portion of the total power and raising the power in the second portion of the total power, but maintaining the total power at the same level as the total power during the transmit cycle. The method further includes, after the probe cycle, raising the power in the first portion of the total power and lowering the power in the second portion of the total power.

Dynamic multi-channel power management for neighbor discovery

Growing community of inventors

Draper, UT, United States of America

Patrick L Newbold