Toyota Jidosha Kabushiki Kaisha

Yamaha Hatsudoki Kabushiki Kaisha

Osamu Hosokawa

Masanao Idogawa

Noboru Takagi

Hirohisa Kishi

Jun Maemura

Takahide Kyuuma

Koichi Yonezawa

Takayuki Demura

Senji Kato

Jun Takahashi

Masahiko Teraoka

Takeyasu Muraishi

To quickly suppress a detected decrease in engine speed in a direct injection internal combustion engine (), a fuel injection quantity is increased by performing a supplementary fuel injection in addition to a normal fuel injection.

Fuel injection control apparatus and method for direct injection internal combustion engine

In a direct injection internal combustion engine which switches a fuel injection mode between a batch injection in which fuel is injected once and a split injection in which fuel is injected at a plurality of timings, a fuel increase amount is set larger for the split injection than for the batch injection when increase-correcting a fuel injection quantity set based on an engine operating state.

A valve characteristic control apparatus is provided in an internal combustion engine including a variable valve mechanism that can change at the least, among valve characteristics of an exhaust valve, a closing timing of the exhaust valve, and in which a number of injections of fuel is changed during one engine cycle. The valve characteristic control apparatus sets the closing timing of the exhaust valve to a retard side during an engine warming up operation. When setting to the retard side is performed, if two injections are performed, an exhaust side target displacement angle VTTex of the exhaust valve is calculated based on a dual injection use map. On the other hand, if one injection is performed, the exhaust side target displacement angle VTTex of the exhaust valve is calculated based on a single injection use map.

Valve characteristic control apparatus for internal combustion engine

A requested injection amount of fuel necessary during ignition cut-off at the time of start at an extremely low temperature is calculated (step ST), injection start timing and injection end timing between which wetting of a spark plug by fuel is less likely are set (step ST), and the number of times of ignition cut-off is calculated based on the injection start timing and the injection end timing and the requested injection amount (step ST). The injection start timing and the injection end timing are thus restricted to timings between which plug wetting is less likely, and the number of times of ignition cut-off is calculated based on the injection start timing and the injection end timing and the requested injection amount, so that wetting of the spark plug by fuel at the extremely low temperature can be avoided even in an in-cylinder direct-injection engine.

Control device of in-cylinder direct-injection internal combustion engine

A fuel-injected engine is operated in a compression stroke injection mode or an intake stroke injection mode. The intake flow rate appropriate for the compression stroke injection mode is greater than that of the intake stroke injection mode. When the engine is cold, the ECU determines the amount of fuel injected in accordance with the actual intake flow rate. The ECU controls a throttle valve such that the intake flow rate is appropriate for the selected fuel injection mode before the fuel injection mode is actually switched. As a result, fluctuations of the engine speed caused by switching the fuel injection mode are reduced.

Control apparatus and control method for direct injection engine

A control apparatus for a cylinder injection type internal combustion engine in which the fuel injection mode of the engine is switched between a compression stroke injection and an intake stroke injection. When the engine is cold, the compression stroke injection is selected for the fuel injection mode so that injected fuel collides with the top surface of a piston and is directed toward the vicinity of a spark plug. When the fuel injection mode is switched from the compression stroke injection to the intake stroke injection, the ignition timing is delayed during the execution of the intake stroke injection from when the fuel injection mode is switched until a predetermined period elapses compared with a case when the fuel injection mode is not switched.

Control apparatus for cylinder injection type internal combustion engine

An engine has an injector, which directly injects fuel into a combustion chamber. When the coolant temperature during the cranking of the engine is low, an ECU controls the injector such that the engine is operated in a compression stroke injection mode. When the engine is operated in the compression stroke injection mode, the ECU controls the injector to advance the fuel injection timing in accordance with an increase of the coolant temperature. As a result, the engine reduces the amount of unburned discharge gas, provides improved ignition and combustion, and provides stable idling.

Fuel injection control apparatus and fuel injection control method for direct injection engine

A direct-fuel-injection-type internal combustion engine is equipped with an injector for injecting fuel directly into a combustion chamber of a cylinder. A controller controls the degree of opening of a throttle valve for adjusting the amount of air drawn into the combustion chamber and sets the throttle valve to a closed valve state by setting the degree of opening of the throttle valve to a degree of opening that is on the closed valve side of a post-engine start target degree of opening, when the engine is to be started. After it is determined that a start of the engine has been accomplished, the controller opens the throttle valve by gradually increasing the degree of opening of the throttle valve from the degree of opening of the closed valve state to the post-engine start target degree of opening.

Growing community of inventors

Toyota, Japan

Osamu Hosokawa