Denso Corporation

Noriaki Iwase

Yasuo Mukai

Hisashi Iida

Haruyuki Urushihata

Yasuhiro Kawakatsu

Jun Hasegawa

Yoshihiro Majima

Masaomi Inoue

Naoyuki Kamiya

Hideyuki Maeji

When executing a Local-learning, an air-fuel ratio detecting time is corrected so that a dispersion of detection values of an air-fuel ratio sensor becomes a maximum value in one cycle of an engine. While executing a cylinder-by-cylinder air-fuel ratio control, a Global-learning is executed. In the Global-learning, the air-fuel ratio detecting time is corrected based on a relationship between a variation in estimated air fuel ratio of each cylinder and a variation in fuel quantity correction value of each cylinder. In the Global-learning, a computer computes a correlation coefficient between the variation in estimated air-fuel ratio and the variation in fuel quantity correction value of the cylinder for each case where the cylinder assumed to correspond to the estimated air fuel ratio is hypothetically varied in multiple ways. Then, the air-fuel ratio detecting time is corrected so that this correlation coefficient becomes a maximum value.

Cylinder-by-cylinder air-fuel ratio controller for internal combustion engine

An individual cylinder air-fuel ratio estimation of estimating an air-fuel ratio of an individual cylinder is performed on a sensed value of an air-fuel ratio sensor set in an exhaust gas collection part of an engine, and an individual cylinder air-fuel ratio control of controlling the air-fuel ratio of the individual cylinder is performed in such a way that a variation in the air-fuel ratio between the cylinders becomes small on the basis of an estimated air-fuel ratio of the individual cylinder. Further, it is determined whether or not a misfire of the engine is caused and when it is determined that the misfire of the engine is caused, the individual cylinder air-fuel ratio estimation and the individual cylinder air-fuel ratio control are stopped and an individual cylinder correction value by the individual cylinder air-fuel ratio control is reset. In this way, it is possible to avoid the individual cylinder air-fuel ratio control from being performed continuously as usual in a state where the air-fuel ratio of the individual cylinder cannot be controlled correctly due to the effect of the misfire.

Individual cylinder air-fuel ratio control device of internal combustion engine

An air-fuel-ratio of each cylinder is estimated based on a detection value of an air-fuel-ratio sensor. An air-fuel-ratio detection timing determination is executed to determine whether a deviation in air-fuel-ratio detection timing exists based on the estimated air-fuel-ratio while the cylinder-by-cylinder air-fuel-ratio control is performed. An observation residual is computed based on the detection value of the air-fuel-ratio sensor and the estimated air-fuel-ratio. When the observation residual is greater than or equal to a specified threshold value, the air-fuel-ratio detection timing determination is prohibited. Therefore, when the observation residual is still large before the estimated air-fuel-ratio of each cylinder is converged, or when the observation residual is still large due to a temporal deterioration in estimating accuracy of the estimated air-fuel-ratio, the air-fuel-ratio detection timing determination can be prohibited.

Cylinder-by-cylinder air-fuel-ratio controller for internal combustion engine

An ECU executes a cylinder-by-cylinder air-fuel-ratio control in which an air-fuel-ratio of each cylinder is estimated based on a detection value of an air-fuel-ratio sensor to adjust the air-fuel-ratio of each cylinder. Further, the ECU computes a learning value of a correction quantity for each cylinder, which is obtained by executing the cylinder-by-cylinder air-fuel-ratio control. Then, the ECU determines whether the estimated air-fuel-ratio has converged according to whether the estimated air-fuel-ratio of each cylinder has been closer to a target value than a specified value for not less than a specified time period. A computation of the learning value is prohibited until the estimated air-fuel-ratio has converged. Therefore, it can be avoided to compute the learning value based on the fuel correction quantity that is obtained when the estimated air-fuel-ratio has not converged yet.

An abnormality diagnosis device is for an exhaust heat recovery equipment including an exhaust heat absorption part absorbing exhaust heat from an engine, a heat release part releasing at least part of the heat absorbed by the absorption part to engine coolant, a circulation loop passing through the absorption part and the release part, the medium circulating around the loop, and an opening and closing valve disposed in the loop between the absorption part and the release part. The equipment closes the valve to stop circulation of the medium when coolant temperature is a preset temperature or above. The device includes an abnormality determination device for determining whether the valve is in an abnormal opening state based on a heat amount transmitted from exhaust heat to coolant through the equipment, when coolant temperature is the preset temperature or above and thereby the valve is closed if the valve is normal.

Abnormality diagnosis device for exhaust heat recovery equipment

A control duty is obtained, which asymptotically makes the output of a control subject consistent with an output of a reference model. The output of the control subject simulates a dynamic characteristic of a variable valve timing controller, and the output of the reference model simulates an ideal input-output characteristic of the variable valve timing. The control duty makes a difference between the output of the reference model and an actual valve timing small enough. A parameter of a controller is consecutively corrected to make the difference small by means of a parameter correcting mechanism when the dynamic characteristic of the variable valve timing controller is varied due to a variation of an operating environment thereof so that the difference becomes large.

Controller for automobile

A control unit employed in a variable valve timing apparatus vibrates a control signal for controlling an oil-pressure control valve. If the vibration center of the duty value of the control signal for driving the oil-pressure control valve lies in a dead band, the vibration takes the duty value to the outside of the dead center temporarily. Thus, even if the center value of the control signal lies in the dead band, the valve timing of the oil-pressure control valve changes with variations in control signal. As a result, the width of the dead band appears small or to have a value of zero. Accordingly, the response characteristic of variations in valve timing to the variations in control signal is improved. The vibration of the control signal is also effective for detection of a width of the dead band.

Growing community of inventors

Obu, Japan

Noriaki Iwase