Integran Technologies Inc.

Nandakumar Nagarajan

Klaus Tomantschger

Francisco Gonzalez

Diana Facchini

Gino Palumbo

Jonathan McCrea

Uwe Erb

Jared J Victor

Mioara Neacsu

Konstantinos Panagiotopoulos

Herath Katugaha

Iain Brooks

Peter Lin

John Kratochwil

Karl Aust

Dan Woloshyn

Yusuf Bismilla

Mike Uetz

Francisco Gonzales

Diana Faccini

Jonathan Mccrea

Polycrystalline materials are prepared by electrodeposition of a precursor material that is subsequently heat-treated to induce at least a threefold increase in the grain size of the material to yield a relatively high fraction of 'special' low &#x3a3; grain boundaries and a randomized crystallographic texture. The precursor metallic material has sufficient purity and a fine-grained microstructure (e.g., an average grain size of 4 nm to 5 &#x3bc;m). The resulting metallic material is suited to the fabrication of articles requiring high mechanical or physical isotropy and/or resistance to grain boundary-mediated deformation or degradation mechanisms.

Electrodeposition method for preparing polycrystalline copper having improved mechanical and physical properties

A method for electrodepositing a coating/free-standing layer on a workpiece in an electrolytic cell includes moving the workpiece and an anode applicator tool having a consumable anode insert relative to each other; anodically dissolving a metal from the insert and cathodically depositing the metal on the workpiece; providing flow of electrolyte solution through the insert to ensure that greater than 90% of the anodic reaction is represented by dissolution of the metal; recirculating collected electrolyte solution exiting the electrolytic cell through the insert; applying an electric current to the electrolytic cell; maintaining a concentration of the anodically dissolved metal within &#xb1;25% of each Ampere-hour per liter of electroplating solution; and creating a cathodic electrodeposit on the workpiece which includes the anodically dissolved metal, the chemical composition of the deposit varying by less than 25% in the deposition direction over a selected thickness of up to 25 microns of the deposit.

Porous, flow-through consumable anodes for use in selective electroplating

Articles containing fine-grained and/or amorphous metallic coatings/layers on at least part of their exposed surfaces are imprinted with surface structures to raise the contact angle for water in the imprinted areas at room temperature by equal to or greater than 10&#xb0;, when compared to the flat and smooth metallic material surface of the same composition.

Metallic articles with hydrophobic surfaces

Method for preparing polycrystalline structures having improved mechanical and physical properties

Anode applicators include consumable anodes, that can be operated in a non-stationary mode and are insensitive to orientation, are used in selective plating/brush electrodeposition of coatings or free-standing components. The flow-through dimensionally-stable, consumable anodes employed are perforated/porous to provide relatively unimpeded electrolyte flow and operate at low enough electrochemical potentials to provide for anodic metal/alloy dissolution avoiding undesired anodic reactions. The consumable anodes include consumable anode material(s) in high surface area to reduce the local anodic current density. During electroplating, sufficient electrolyte is pumped through the consumable anodes at sufficient flow rates to minimize concentration gradient and/or avoid the generation of chlorine and/or oxygen gas and/or undesired reaction such as the anodic oxidation of P-bearing ions in the electrolyte. The active consumable anode material(s) can have a microstructure which is fine-grained and/or amorphous to ensure a uniform anodic dissolution.

Flow-through consumable anodes

Metal-clad polymer articles containing structural fine-grained and/or amorphous metallic coatings/layers optionally containing solid particulates dispersed therein. The fine-grained and/or amorphous metallic coatings are particularly suited for strong and lightweight articles, precision molds, sporting goods, automotive parts and components exposed to thermal cycling although the CLTE of the metallic layer and the one of the substrate is mismatched. The interface between the metallic layer and the polymer is suitably pretreated to withstand thermal cycling without failure.

Structural metal-clad polymer article

Metal-clad polymer articles containing structural fine-grained and/or amorphous metallic coatings/layers optionally containing solid particulates dispersed therein, are disclosed. The fine-grained and/or amorphous metallic coatings are particularly suited for strong and lightweight articles, precision molds, sporting goods, automotive parts and components exposed to thermal cycling although the coefficient of linear thermal expansion (CLTE) of the metallic layer and the substrate are mismatched. The interface between the metallic layer and the polymer is suitably pretreated to withstand thermal cycling without failure.

Metal-clad polymer article

Super-hydrophobic and self-cleaning articles produced by imprinting exposed surfaces with suitable fine-grained and/or amorphous metallic embossing dies to transfer a dual surface structure, including ultra-fine features less than or equal to 100 nm embedded in and overlaying a surface topography with macro-surface structures greater than or equal to 1 micron are disclosed.

Method of making articles with super-hydrophobic and/or self-cleaning surfaces

An article includes an electrodeposited metallic material including Co with a minimum content of 75% by weight. The metallic material has a microstructure which is fine-grained with an average grain size between 2 and 5,000 nm and/or an amorphous microstructure. The metallic material forms at least part of an exposed surface of the article. The metallic material has an inherent contact angle for water of less than 90 degrees at room temperature when measured on a smooth exposed surface portion of the metallic material which has a maximum surface roughness Ra of 0.25 microns. The metallic material has an exposed patterned surface portion having surface structures having a height of between at least 5 microns to about 100 microns incorporated therein to increase the contact angle for water at room temperature of the exposed patterned surface portion to over 100 degrees.

Electrodeposited metallic materials comprising cobalt

Articles with super-hydrophobic and/or self-cleaning surfaces and method of making same

Metal-clad polymer articles containing structural fine-grained and/or amorphous metallic coatings/layers optionally containing solid particulates dispersed therein, are disclosed. The fine-grained and/or amorphous metallic coatings are particularly suited for strong and lightweight articles, precision molds, sporting goods, automotive parts and components exposed to thermal cycling although the CLTE of the metallic layer and the one of the substrate is mismatched. The interface between the metallic layer and the polymer is suitably pretreated to withstand thermal cycling without failure.

Growing community of inventors

Burlington, Canada

Nandakumar Nagarajan