Other

Oceaneering International, Inc.

Ecosse Subsea Systems Limited

Oceaneering International Services Limited

Wilson, Michael, W. N.

Michael W N Wilson

Stuart P Moir

A water-driven turbine has an elongated endless conveyor with down and up streaming straightaways connected by travel-reversing turns. Paddles mounted on the conveyor present high resistance to waterflow on the downstream straightaway and low resistance to waterflow or the atmosphere on the upstream straightaway, the differential allowing the flow of water to continuously drive the conveyor which is connected to a power take-off shaft facilitating connection to a variety of energy-harnessing systems. The turbine can be towed, self-driven or mooring line manipulated to a flow site and is operable in unidirectional flows such as rivers and reversing flows such as tides at depths from surface to bottom. The paddles can be mounted or changed on shore, at the flow site and anywhere in between. The turbine is efficient in low and high velocity water flow, not easily damaged by floating debris, cavitation free and fish, mammal and environmentally friendly.

Water-driven elongated-conveyor turbine and method of using a water-driven elongated-conveyor turbine

A method for governing the elevation, attitude and structural integrity of a pressure-containing vessel in a body of liquid counterbalances flotation and incompressible ballast mediums against each other in separate serial compartments. Varying the quantity of incompressible ballast medium allows control of the elevation and attitude of the vessel. If the flotation medium is compressible, varying the quantity of flotation medium allows control of the ambient pressure of the vessel. The method facilitates floating and towing and laying of an undersea pipeline on, to and at a deep water site.

Method of governing the elevation, attitude and structural integrity of a pressure-containing vessel in a body of liquid

A BAS plow creates a V-trench along the linear route of a pipeline path and an instrumented bottle moving with the BAS plow collects BAS data indicative of the pitch, roll, heading, yaw, three dimensional positioning, speed and depth of the chassis, the shearing force applied to the seabed material and the applied tow force. The bottle can be swapped to collect the acquired data or an umbilical can be used to provide a real time stream of data. The BAS plow can simultaneously backfill the created trench, leaving an undisrupted seabed, or the pipeline can be laid in the BAS trench, which can also be made deeper and wider by additional trench cutting passes, significantly reducing the total time required for combined BAS and pipeline laying processes. The BAS plow can be released and retrieved over-the-stern of a towing vessel.

Seabed backfill plow and method

A seabed trenching plow has a chassis, a sled and a towing assembly. The towing assembly has a pair of wings extending laterally from each side of the chassis. The wings are aligned on an axis transverse to the chassis and adapted for connection to a towing line. The transverse axis is forward of the center of gravity of the plow and rearward of the sled, affording an over the stern releasable and retrievable trenching plow of sufficient weight and strength to excavate a three meter trench in a single pass. To assess the protective capabilities of the trench, a threshold signal indicative of a desired composition of seabed-trench soil is compared with a real-time data signal indicative of the actual to produce an alarm signal when the real-time data signal is not protective-capability compliant with the threshold signal.

Over-the-stern deep digging trenching plow with instrumentation for assessing the protective capabilities of a seabed trench

A seabed plow capable of over-the-stern release and retrieval is usable in any of boulder clearing, trench cutting and backfill modes. In its boulder clearing mode, the plow uses its skid in torquing configuration followed by moldboards to push boulders out of the path to be trenched. In the trench cutting mode, the plow uses the skid in the same configuration with its share and moldboards for initial trench depth and the same share and moldboards with moldboard extensions for increasing trench depth in subsequent passes. In the backfill mode, the plow uses its skid in trench-straddling configuration following a blade with a passage designed to discharge fragmented spoil directly onto the pipe being covered. Thus, a single plow can be reconfigured for all modes for release and retrieval to and from a relatively small vessel without use of heavy lifting equipment.

Seabed plow capable of over-the-stern release and retrieval in any of boulder clearing, trenching and backfill configurations

A jetting system for an undersea trencher has jetting conduits extending aftward of its trench-cutting jetting swords. Jetting conduit nozzles direct liquid radially from their jetting conduits into the trench after the trench is excavated by the jetting sword cutting nozzles. The jetting conduits direct sufficient liquid into the trench to maintain the mix of trenched soil and water in the trench along the length of the conduits at not more than a super-critical density, extending the distance in which the product being laid in the trench is able to descend in the trench and increasing the likelihood that the product will be buried at the intended trench depth.

Jet trenching system

A jetting system for an undersea trencher has jetting conduits extending aftward of its trench-cutting jetting swords. Jetting conduit nozzles direct liquid radially from their jetting conduits into the trench after the trench is excavated by the jetting sword cutting nozzles. The jetting conduits direct sufficient liquid into the trench to maintain the mix of trenched soil and water in the trench along the length of the conduits at not more than a super-critical density.

A BAS plow creates a V-trench along the linear route of a pipeline path and an instrumented bottle moving with the BAS plow collects BAS data indicative of the pitch, roll, heading, yaw, three dimensional positioning, speed and depth of the chassis, the shearing force applied to the seabed material and the applied tow force. The bottle can be swapped to collect the acquired data or an umbilical can be used to provide a real time stream of data. The Bas plow can simultaneously backfill the created trench, leaving an undisrupted seabed, or the pipeline can be laid in the BAS trench, which can also be made deeper and wider by additional trench cutting passes, significantly reducing the total time required for combined BAS and pipeline laying processes. The BAS plow can be released and retrieved over-the-stem of a towing vessel.

Method and apparatus for performing burial assessment surveys

In undersea laying pipeline which is being unreeled from a ship spool in a plastically deformed state, the pipeline is straightened from the plastic state into a behaviorally elastic state as it is unreeled. The straightened pipeline is dispensed in the behaviorally elastic state through a downstream pipe tensioner while the straightened pipeline upstream of the tensioner is maintained in the behaviorally elastic state. The pipeline laying assemblage may include a flange weld station immediately upstream of the tensioner and/or an anode weld station downstream of the tensioner in the above-waterline freeboard of the ship. The pipeline laying method reduces the number of components and the size and cost of the ships in comparison to conventional systems.

Assemblage and method for undersea laying of pipeline from a ship spool

A method and system for storing, delivering and spooling pipelines, such as underwater pipelines used in off-shore well production systems, enables continuous pipeline reeling operations for multi-mile pipelines without the need for welding stops, a spool base of corresponding multi-mile length, a straight line path from storage to ship and/or stern mooring of the reel carrying vessel. Bending radii for the pipeline from welding to reeling are held to a determined minimum within the range of plastic deformation radii of the pipeline and preferably within the range of elastic bending radii of the pipeline.

Growing community of inventors

Aberdeenshire, United Kingdom

Michael W N Wilson