Robert Boschgmbh

Michael Ulmer

Jens Otterbach

Peter Taufer

Harald Tschentscher

Jochen Schomacker

Christian Ohl

Hartmut Schumacher

Oliver Kohn

Andreas Rupp

Gerald Nitsche

Boris Adam

Pascal Kocher

Achim Henne

Davor Lukacic

Bernhard Straub

Thomas Huber

Rolf-Juergen Recknagel

Dirk Ullmann

Rolf Aidam

Ingbert Gerngross

A method for checking an interface module, the interface module returning to the processor, using a second data message, stored values representing sensor values, after a request for a test by a processor using a data message. Using these firm sensor values, the processor can check the functioning of the interface module and its own algorithm. A safety module, which also picks up the sensor values, also checks its functioning with them, since the safety module is a redundant hardware path to the processor and is used as a plausibility check for the release decision of means of restraint. The interface module is changed into a test mode as soon as it receives the first data message from the processor, and it then suppresses the transmission of the real sensor values which were received from connected sensors.

Method for checking an interface module

A sensor has a transmitter module for transferring data via a line, the sensor receiving power via the line. At a point in time in which the sensor receives a first power level, it transmits the data for a first time interval. A second sensor which is connected to the line in parallel to the first sensor then transmits its data for a second time interval after the first time interval. A timing sequence control system in the two sensors which is triggered by the point in time of reception of the power ensures the subsequent transmission by the first and second sensor.

Sensor system and method for sequential transmission of data

A method for transmitting data from at least one sensor to a control unit is described, a value range, which is available for encoding the data to be transmitted, being divided into three portions. The first portion is used for the sensor values. The second portion is used for status signals and error signals, and the third portion is used for sensor identification data, the three portions being separated from one another and following in succession.

Method for transmitting data from at least one sensor to a control device

A method of data transmission from a sensor to a control unit and a sensor and control unit are described, the sensor transmitting both differential values and absolute values. The differential values are analyzed in the control unit to perform the function provided, and the absolute values are analyzed for the plausibility check of the function.

Method for transmitting data from sensor to a control unit, and a corresponding sensor and control unit

A device for impact sensing is described which detects an impact by a pressure, a normalized signal being supplied to a processor for analyzing the pressure signal. This normalization may occur either in the pressure sensor, by the sensor element itself or by a signal preprocessor, or in the processor.

Device for impact sensing

A device for monitoring a processor is described. A watchdog simultaneously monitors the system clock, the software base functions and performs a check of the tests of the system components of the processor. If an error is detected, the watchdog communicates this to the processor, an error counter is incremented and at least one device that is connected to the processor is blocked. If the error counter attains a predetermined value, the block is continued until the device of the present invention is deactivated. If an additional error is detected during a blocking time, the blocking time is extended.

Device for monitoring a processor

A device for triggering ignition circuits is provided, a coupling being provided between a positive output stage and negative output stage of different pairs. Each positive and each negative output stage is assigned a diagnostic unit and a drive circuit.

Device for triggering ignition circuits

A method for transmitting data from at least one sensor to a control unit via an appropriate two-wire line is described. The method is used to identify any sensor at the control unit and to implement a plurality of logical channels via the appropriate two-wire line. The at least one sensor receives the necessary electrical energy from the control unit via the two-wire line and then transmits the sensor-specific data.

Method for transmitting data from at least one sensor to a control unit

A device for controlling firing circuits for restraining devices, a processor and a safety IC for controlling the restraining devices being connectable to the firing circuit control, and the firing circuit control having blocking inputs and blocking registers for the blocking of groups of connectable firing circuits; the processor setting the blocking registers after switching-on (of the device) and logically linking the firing circuit control data of the blocking inputs and the blocking registers with one another, so as to block individual groups of firing circuits. Thus it is especially possible individually to block firing circuits for air bags in dependence upon the degree of occupancy and the classification of the occupants in a vehicle. Setting the blocking inputs and the blocking registers takes place shortly after switching-on (of the device), after function tests of the IC's have been conducted. Besides the blocking inputs for individual control, the firing circuit control also has blocking inputs for blocking all plus and minus output stages.

Device for controlling firing circuits for restraining devices

A device for triggering ignition circuits is used to increase safety without additional expenditures in the form of hardware or wiring. Plus and minus output elements of various ICs are used for this purpose. Ignition circuit diagnosis is now also distributed over two ICs. Ignition circuit diagnosis includes, in particular, the resistance measurement of the respective ignition circuit. Each substrate, in other words IC, therefore has at least one plus and one minus output element.

A device for data transmission between vehicle sensors and a control unit, which is used to decode data telegrams having sensor data from the vehicle sensors and to reformat them into SPI (serial peripheral interface) data telegrams. Furthermore, an interface module of the control unit transmits the SPI data telegrams to the processor of the control unit. By using an alter bit, the processor determines whether to retrieve the newest sensor data or the preceding sensor data. The interface module converts the sensor data in each case into a 10-bit data field of an SPI data telegram, into which the interface module may supplement missing data. By counting out the edges, it is possible for the interface module to recognize the data telegrams from the sensors.

Device for data transmission between vehicle sensors and a processor in a controller

A device and a method are proposed for controlling firing circuits for an element of restraint, individual transistors of the output stages being controlled by bit combinations, and impermissible bit combinations lead to an error message to a processor. In addition, a firing current is measured, in order to estimate a firing energy from it, so that efficient energy management can be carried out. Furthermore, determination of the firing current makes it possible to update a crash protocol as to whether the firing circuit was activated or not. When a voltage of the energy reserve is exceeded, it is further proposed to switch over to pulse operation for operating the output stages. Thereby a greater resistance to short-circuits and a higher efficiency are achieved.

Growing community of inventors

Moessingen, Germany

Michael Ulmer