Linear Technology Corporation

Michael Paul

Jeffrey Lynn Heath

Heath Stewart

David McLean Dwelley

David Stover

David M Stover

The invention pertains to systems where DC power is supplied by a PSE to a PD, such as over differential data wire pairs. IEEE standards require a minimum current to be drawn from the PD in order for the PSE to continue supplying the DC voltage. If the PD is in a low power mode, the PSE will normally discontinue supplying the DC voltage, which then requires a new detection and classification routine for powering up again. To avoid this, a 'maintain power signature' controller provides a periodic current pulse by a current source connected between the PD input and the PD's full bridge rectifier. Any droop in the DC voltage that reverse biases the full bridge rectifier while the PD is in its low power mode will not affect the current pulse, so the PSE continues to supply the DC voltage.

Maintain power signature controller at power interface of PoE or PoDL system

A PSE includes a PSE controller that performs a handshaking routine with any PDs connected to the data wire pairs and spare wire pairs and applies power to the data wire pairs and spare wire pairs, via a switch, if certain conditions are met. Two different levels of currents are supplied to different terminals of the PSE controller that are connected to the data wire pairs and the spare wire pairs, and the resulting voltages are measured. The voltages are used to determine the PD impedances at the ends of the data wire pairs and spare wire pairs to determine whether a PD is connected to the data wire pair, whether another PD is connected to the spare wire pair, or whether a single PD is connected to both the data wire pairs and the spare wire pairs.

PSE controller in PoE system detects different PDs on data pairs and spare pairs

In a method performed by a PoE system, a PSE is able to detect whether a PD is compatible for receiving power via four wire pairs in the standard Ethernet cable. The PSE provides a current limited voltage to a first and second pair of wires in the cable, during a detection phase, to detect a characteristic impedance of the PD. In the PSE, a first resistor is connected to a third wire pair and a second resistor is connected to a fourth wire pair. During the detection phase, the PSE detects the relative currents through the resistors. If the currents are the same, then the PSE knows the PD is able to receive power via the four wire pairs. The PSE then applies the full PoE voltage to the first and second wire pairs and connects the third and fourth wire pairs to a low voltage via a MOSFET.

Detection scheme for four wire pair Power Over Ethernet system

Power Sourcing Equipment (PSE) provides a PoE supply voltage over data wires to a Powered Device (PD). A PSE controller controls a first FET that couples the PoE voltage to the data wire pairs and controls a second FET that couples the data wire pairs to the spare wire pairs. Upon powering up, the PSE controller keeps the two FETs open and performs a detection routine on any devices connected to the data pairs and spare pairs. If a PoE-compatible PD is detected as being coupled to the data pairs, the first switch is closed. If it is determined that the PoE voltage should also be coupled to the spare pairs, the second FET is also closed. The method prevents the PoE voltage from being applied to the spare pairs when the device connected to the spare pairs is not PoE compatible and maintains backwards compliance with IEEE PoE PDs.

Power over Ethernet on data pairs and spare pairs

A system for combining power to a load in a Powered Device (PD) using Power Over Ethernet (PoE) receives power from a first channel and power from a second channel, via four pairs of wires. A MOSFET bridge for each channel is initially disabled. A bridge controller IC simultaneously senses all the voltages and controls the bridge MOSFETs. The bridge controller IC also contains a first PoE handshaking circuit. A second PoE handshaking circuit is external to the bridge controller IC and operates independently. The body diodes in the MOSFET bridge initially couple the first channel to the second PoE handshaking circuit while isolating the second channel. The second handshaking circuit then couples the first channel to the load. The first handshaking circuit then carries out a PoE handshaking routine for the second channel. Ultimately, the bridge controller controls the bridge MOSFETs to couple both channels to the load.

Growing community of inventors

Santa Barbara, CA, United States of America

Michael Paul