Delphi Technologies, Inc.

Aptiv Technologies Limited

Michael I Chia

Ehsan Samiei

Kevin J Hawes

Premchand Krishna Prasad

Ronald Helmut Haag

Walter Kirk Kosiak

Robert J Cashler

Adil Ansari

A lane keeping system includes an absolute pressure sensor located in a door on each of opposing sides of a vehicle. Each sensor generates a signal indicative of a door cavity pressure on that side of the vehicle. A safety restraint system (SRS) controller is in communication with the pressure sensor. The SRS controller is configured to determine a collision event in response to the signal (e.g., increased pressure in the door as it is crushed) and activate a safety restraint component in response to the determined collision event. A lane keeping system (LKS) controller is in communication with the pressure sensors. The LKS controller determines a lateral wind force on the vehicle in response to the signal from each pressure sensor. The LKS controller determines a correction in response to the determined lateral wind force to maintain the vehicle along a desired path.

Lane keeping system for autonomous vehicle in wind conditions

A vehicle-control system suitable for use on an automated vehicle includes a human-machine-interface and a controller. The human-machine-interface accepts an input from an operator of a host-vehicle. The controller is in communication with the human-machine-interface. The operator inputs a notification to the human-machine-interface. The notification indicates that the operator detects a circumstance that suggests a presence of the emergency-vehicle on the roadway that has not been detected by the system. The controller drives the host-vehicle in accordance with rules governing an operation of vehicles proximate to an emergency-vehicle stopped alongside a roadway.

Automated vehicle control system

A lane keeping system for a vehicle includes a first roll angle sensor configured to provide a first signal indicative of dynamic vehicle body roll. A second roll angle sensor is configured to provide a second signal indicative of an angle between vehicle sprung and unsprung masses. A lane keeping system (LKS) controller is in communication with the first and second roll angle sensors. The LKS controller is configured to discern a vehicle roll angle in response to the first and second signals based upon effects of a lateral wind force on the vehicle. The LKS controller is configured to produce a correction in response to the determined lateral wind force effects to maintain the vehicle along a desired path.

Lane keeping system for autonomous vehicle in wind conditions using vehicle roll

A lane-control system suitable for use on an automated vehicle comprising a camera, a lidar-sensor, and a controller. The camera captures an image of a roadway traveled by a host-vehicle. The lidar-sensor detects a discontinuity in the roadway. The controller is in communication with the camera and the lidar-sensor and defines an area-of-interest within the image, constructs a road-model of the roadway based on the area-of-interest, determines that the host-vehicle is approaching the discontinuity, and adjusts the area-of-interest within the image based on the discontinuity.

Vision sensing compensation

A lane-keeping system suitable for use on an automated vehicle includes a camera, an inertial-measurement-unit, and a controller. The camera is configured to detect a lane-marking of a roadway traveled by a vehicle. The inertial-measurement-unit is configured to determine relative-motion of the vehicle. The controller in communication with the camera and the inertial-measurement-unit. When the lane-marking is detected the controller is configured to steer the vehicle towards a centerline of the roadway based on a last-position, and determine an offset-vector indicative of motion of the vehicle relative to the centerline of the roadway. When the lane-marking is not detected the controller is configured to: determine an offset-position relative to the last-position based on information from the inertial-measurement-unit, determine a correction-vector used to steer the vehicle from the offset-position towards the centerline of the roadway based on the last-position and the offset-vector, and steer the vehicle according to the correction-vector.

Lane-keeping system for automated vehicles

A technique for providing better detection of close range truck trailers for a motor vehicle with Stop and Go Adaptive Cruise Control determines if a range parameter to a target requires modification if such target is a truck trailer, for example. Truck trailer geometry is such that a standard adaptive cruise control system may have difficulty accurately determining the range to the rearmost position of the truck. The technique determines an initial range from the motor vehicle to a target. Then, the technique determines whether the range rate of the target is above a predetermined rate. When the range rate of the target is not above the predetermined rate, the technique determines whether the initial range to the target is less than a current range to the target. If so, the technique provides an adjusted range, which is then utilized in the control operation of the motor vehicle.

Technique for detecting truck trailer for stop and go adaptive cruise control

An absolute position sensor having a low power mode includes a sensing device for sensing position of an object such as a power door, a power input for inputting power to the sensing device, and an output for supplying an output signal indicative of the sensed position. The sensor also includes a controller that receives the output signal and controls power supplied to the power input. The controller determines when the output signal does not change by a predetermined amount and controls the power input to reduce power when the output signal does not change by the predetermined amount. The controller further reapplies continuous full power to the power input when the output signal changes by the predetermined amount.

Low power absolute position sensor and method

An electronic position sensor for use with a power operated vehicle accessory, such as a power liftgate. The position sensor includes an elongated resistive circuit that is mounted such that it is stationary and extends along the path of a track portion of the power operated accessory. The position sensor further includes a contact nub mounted to a link member that moves within the track portion such that the contact nub is slidingly biased against the elongated circuit. As the link member moves under the force of a motor-driven output gear, the contact nub slides along the surface of the resistive circuit, thereby affecting the overall resistance of the circuit. The position sensor uses the overall resistance to provide an electronic position signal to an ECU, wherein the signal is indicative of the absolute position of the power operated accessory. Accordingly, the electronic position sensor is capable of providing an electronic signal that enables the ECU to track the absolute position of the power operated accessory.

Growing community of inventors

Cicero, IN, United States of America

Michael I Chia