Ut-battelle, Inc.

Excavation Engineering Associates, Inc.

Levent Ozdemir

Craig A Blue

Louis F Aprigliano

William H Peter

James E Friant

Peter G Engleman

Frank Wong

Tibor G Rozgonyi

A coating steel component with a pattern of an iron based matrix with crystalline particles metallurgically bound to the surface of a steel substrate for use as disc cutters or other components with one or more abrading surfaces that can experience significant abrasive wear, high point loads, and large shear stresses during use. The coated component contains a pattern of features in the shape of freckles or stripes that are laser formed and fused to the steel substrate. The features can display an inner core that is harder than the steel substrate but generally softer than the matrix surrounding the core, providing toughness and wear resistance to the features. The features result from processing an amorphous alloy where the resulting matrix can be amorphous, partially devitrified or fully devitrified.

In-situ composite formation of damage tolerant coatings utilizing laser

An improved disc type rolling rock cutter, and novel cutterheads employing such cutters. A rock cutter with an improved, simplified structure, with compact bearing, and smooth, rounded blade shape is disclosed. The design incorporates a cutter ring, bearing, and seal into a single cutter ring assembly. The cutter may be assembled and disassembled for rework by a single worker with simple hand tools. Replacement of worn out cutter rings is done quickly and easily by removing the old ring assembly and then sliding a new ring, bearing, and seal assembly on to the cutter shaft. This simplified assembly is achieved by using a comparatively large shaft which is normally in the range of 40-50% of the ring diameter. The shaft design is sufficiently robust to permit a cantilever mount of the cutter. The unique configuration allows 30,000 lbs. or more thrust to be applied to a 5 inch diameter miniature disc. This capacity permits single disc cutter technology to be applied to smaller bits or cutterheads than previously possible. Also, a unique method of shaping and installing hard metal inserts improves cutting efficiency over the life of the cutter, and increases wear life in highly abrasive conditions.

Shielded cutterhead with small rolling disc cutters

An improved disc type rolling rock cutter, and novel cutterheads employing such cutters. A rock cutter with an improved, simplified structure, with compact bearing, and smooth, rounded blade shape is disclosed. The design incorporates a cutter ring, bearing assembly, and seal assembly. The cutter may be assembled and disassembled for rework by a single worker with simple hand tools. Replacement of worn out cutter rings is done quickly and easily by removing the old ring assembly and then sliding a new ring, bearing, and seal assembly on to the cutter shaft. This simplified assembly is achieved by using a comparatively large shaft which is normally in the range of 30-50% of the ring diameter. The shaft design is sufficiently robust to permit a cantilever mount of the cutter. The unique configuration allows 30,000 lbs. or more thrust to be applied to a 5 inch diameter miniature disc. This capacity permits single disc cutter technology to be applied to smaller bits or cutterheads than previously possible. Also, a unique method of shaping and installing hard metal inserts improves cutting efficiency over the life of the cutter, and increases wear life in highly abrasive conditions.

Disc cutter and excavation equipment

An improved rolling disc type cutter, and novel cutterheads employing such cutters. The cutter includes a washer surface and a cutter ring assembly. The cutter ring assembly further includes an annular cutter ring with an interior annulus defining portion and an outer ring portion. A bearing assembly substantially fits into the annulus of the cutter ring in a close fitting relationship with the shaft, so that the cutter ring may rotate with respect to and be supported by said shaft. The bearing assembly includes a bearing and a seal which fits between the washer surface and the cutter ring to form a lubricant retaining seal for the interior annulus portion of the cutter ring. A retainer assembly is used to retain the cutter ring assembly on the shaft, and a cap seals the interior annular portion of the cutter ring assembly so that, in cooperation with the seal and the cutter ring, a lubricant retaining chamber is provided. This simplified cutter design is achieved by using a comparatively large stiff shaft which is preferably in the range of 40-50% of the cutter ring diameter. The stiff shaft design permits cantilever mount of the cutter on a cutterhead. The design allows increased loading of the disk cutter footprint, and permits single disc cutter technology to be applied to small bits or cutterheads. Also, hard metal cutting edge inserts with reduced leading and trailing edge surface curvature are provided.

Growing community of inventors

Golden, CO, United States of America

Levent Ozdemir