Boston Scientific Neuromodulation Corporation

Interlink Electronics, Inc.

Patriot Sensors & Controls, Inc.

Boston Scientific Neuromodulation Company

Lev Freidin

Daniel Aghassian

Joey Y Chen

Thomas W Stouffer

James Dexter Tickle

Carlos Solis Sanchez

Vasily Dronov

Patrick Harold Bair

William Brankin

Thomas Warren Stouffer

A design for an implantable medical device (IMD) is disclosed in which a charging coil and a short-range RF antenna in the IMD's header are physically integrated, and in which the short-range RF antenna includes intentional coupling to the charging coil. A pick-up is capacitively coupled to the charging coil in the header, such as by wrapping the pick-up at least partially around the turns of the charging coil. The charging coil is used to receive power via a magnetic inductive link at a first (preferably lower) frequency, while the combined charging coil and pick-up-together acting as the short-range RF antenna-receive and transmit short-range RF data (e.g., Bluetooth) via a short-range RF data link at a second (preferably higher) frequency. Resonance of the charging coil and short-range RF antenna can be independently tuned, and circuitry can prevent interference between them.

Radio frequency antenna capacitively coupled to a charging coil in an implantable medical device

A charging system for an Implantable Medical Device (IMD) is disclosed having a charging coil and one or more sense coils. The charging coil and one or more sense coils are preferably housed in a charging coil assembly coupled to an electronics module by a cable. The charging coil is preferably a wire winding, while the one or more sense coils are concentric with the charging coil and preferably formed in one or more traces of a circuit board. One or more voltages induced on the one or more sense coils can be used to determine the resonant frequency of the charging coil/IMD coupled system. The determined resonant frequency can then be used to determine the position of the charging coil relative to the IMD. The magnetic field produced from the charging coil may also be driven at the resonant frequency to optimize power transfer to the IMD.

External charger for an implantable medical device for determining position and optimizing power transmission using resonant frequency as determined from at least one sense coil

A design for an implantable medical device (IMD) is disclosed in which a charging coil and a short-range RF antenna in the IMD's header are physically integrated, and in which the short-range RF antenna includes intentional coupling to the charging coil. A pick-up is capacitively coupled to the charging coil in the header, such as by wrapping the pick-up at least partially around the turns of the charging coil. The charging coil is used to receive power via a magnetic inductive link at a first (preferably lower) frequency, while the combined charging coil and pick-up&#x2014;together acting as the short-range RF antenna&#x2014;receive and transmit short-range RF data (e.g., Bluetooth) via a short-range RF data link at a second (preferably higher) frequency. Resonance of the charging coil and short-range RF antenna can be independently tuned, and circuitry can prevent interference between them.

Electrical energy is transcutaneously transmitted at a plurality of different frequencies to an implanted medical device. The magnitude of the transmitted electrical energy respectively measured at the plurality of frequencies. One of the frequencies is selected based on the measured magnitude of the electrical energy (e.g., the frequency at which the measured magnitude of the electrical energy is the greatest). A depth level at which the medical device is implanted within the patient is determined based on the selected frequency. For example, the depth level may be determined to be relatively shallow if the selected frequency is relatively high, and relatively deep if the selected frequency is relative low. A charge strength threshold at which a charge strength indicator generates a user-discernible signal can then be set based on the determined depth level.

External charger with adjustable alignment indicator

Receiver and digital demodulation circuitry for an external controller for communicating with an implantable medical device (IMD) is disclosed. A Digital Signal Processor (DSP) is used to sample received analog data transmitted from the IMD at a lower rate than would otherwise be required for the frequency components in the transmitted data by the Nyquist sampling criteria. To allow for this reduced sampling rate, the incoming data is shifted to a lower intermediate frequency using a switching circuit. The switching circuit receives a clock signal, which is preferably but not necessarily the same clock signal used by the DSP to sample the data. The switching circuit multiplies the received data with the clock signal to produce lower intermediate frequencies, which can then be adequately sampled at the DSP at the reduced sampling rate per the Nyquist sampling criteria.

Receiver and digital demodulation circuitry for an external controller useable in an implantable medical device system

By incorporating magnetic field sensing coils in an external charger, it is possible to determine the position of an implantable device by sensing the reflected magnetic field from the implant. In one embodiment, two or more field sensing coils are arranged to sense the reflected magnetic field. By comparing the relative reflected magnetic field strengths of the sensing coils, the position of the implant relative to the external charger can be determined. Audio and/or visual feedback can then be communicated to the patient to allow the patient to improve the alignment of the charger.

External charger for a medical implantable device using field sensing coils to improve coupling

A system and a method for protecting a connector and a body of a wireless adapter with a geometrical loop antenna. The loop antenna folds over the body of the wireless adapter to protect the connector and the body. The wireless adapter may be used to connect a peripheral device to a host device. The body of the wireless adapter includes a body stop operable for receiving the loop antenna. The system may also include a cap for protecting the connector of the wireless adapter. In this instance, the loop antenna folds over the cap to lock the cap in place on the connector. A cap may also be integrated into the distal end of the loop antenna.

Wireless adapter having foldable geometrically loop-like antenna

A spare voice channel on a cockpit voice recorder (CVR) is used to record flight data. Data from an accelerometer and other sensors in an aircraft are digitized and collected by a microprocessor once each second and are collated and arranged in an industry standard format, and an encoder converts the formatted data into an industry standard code for recording on the CVR. During transmission of data to the CVR, fresh data is collected for the next transmission.

Growing community of inventors

Simi Valley, CA, United States of America

Lev Freidin