Xerox Corporation

Lawrence P Lavery

Stuart Alan Schweid

Robert Michael Lofthus

Guru B Raj

Vincent M Williams

Timothy M Minerd

Peter J Mason

Ross E Schroll

David G Wilcox

Roy W Rivers

Dale C Thomas

David R Shuey

Gary L Hutchinson

Charles F Evans

Larry R Barnard

Dennis Marus

Vernon Edmund Punt

A system for determining the cumulative position and periodic average velocity of a rotating body having an incremental encoder, operatively connected to the body, for generating a series of periodic signals indicative of rotation of the body. The system also includes a high frequency clock for generating clock pulses at a frequency greater than the maximum frequency of the encoder signal, and a timer for controlling the total time of a predetermined sample interval. Also included in the device is a counter for accumulating the number of integral encoder signal cycles that have been completed, an arithmetic logic unit for determining the size of a fractional portion of an encoder signal cycle that was completed between the last integral encoder cycle and the end of the sample interval. Subsequently, the number of integral encoder signal cycles is added to the fractional portion of an encoder cycle to determine the total number of encoder signal cycles completed, whereby the total is then multiplied by an encoder position conversion factor to determine the cumulative position of the rotating body or belt driven therefrom.

High resolution position measurement system

A programmable connector module is equipped with a molded plastic base on which an IC chip is mounted. The plastic base is wired with programmable inputs which can be used to provide a logic 1 or a logic 0 to each input of the IC chip. Tabs or punch holes located on the plastic base can be broken to disconnect an input circuit from ground to allow a logic 1 to be programmed. Two inputs are used to program the configuration of the module and four inputs are used to program the address of the module. The programmable module can be positioned anywhere along a multiplex wire bus and is equipped with connectors for transmitting and receiving data to and from electrical loads along the bus.

Programmable connector module

An automatic development control system having a sensor providing a signal representative of developed toner mass on a patch sample on the photoreceptor. The signal is conveyed to a comparator through signal processing circuits for comparing with a reference signal. The signal processing circuits include digital to analog circuitry also capable of providing analog to digital conversion. The reference signal represents an undeveloped photoreceptor signal normalized to accommodate changing photoreceptor, sensor and operating environment characteristics. A dispenser solenoid activates a toner dispenser through an interrupt mechanism in given increments of time depending upon the error signals generated by the comparator.

Automatic development dispenser control

A video amplifier for use in a document scanning system to provide signals representative of the information content of a scanned document. The amplifier includes an automatic background control portion and an automatic black level adjustment portion to maintain the integrity of the output voltage range independent of the background of the scanned document and throughout the period of time required to scan the entire document. In addition, circuitry is provided for varying the time constant of the automatic background control circuitry to make that circuitry respond quickly to changes of the background toward the 'white' direction. Further, the normally white platen back is provided with a gray leading edge to prevent the automatic background control circuitry from being upset by initial runs of white in the event of an imperfectly registered non-white document.

Amplifier for use in a document scanning system

A facsimile transceiver apparatus is described which includes means for advancing a document to a station at which location the document is line scanned by a laser light beam. A video signal thus formed is transmitted to a remote facsimile apparatus for reproduction of the document. The transceiver further includes an electrostatographic printing station at which station a latent electrostatic image is formed by line scanning a laser light beam over a uniformly charged photoreceptor surface. A means for line scanning at the document scanning station and at the photoreceptor surface includes a laser light source and means for alternatively sweeping the laser light beam across the document at the scanning station or across a charged image retention surface at the printing station. Means are also described for enhancing document feed, resolution, and speed of reproduction.

Facsimile transceiving apparatus

An arrangement for use in a document scanning system to provide background control of signals representative of the information content of a scanned document. An amplifier includes an automatic background control portion and an automatic black level adjustment portion to maintain the integrity of the output voltage range independent of the background of the scanned document and throughout the period of time required to scan the entire document. In addition, circuitry is provided for varying the time constant of the automatic background control circuitry to make that circuitry respond quickly to changes of the background toward the 'white' direction. Further, the normally white platen back at the scanning station is provided with a gray leading edge to prevent the automatic background control circuitry from being upset by initial runs of white in the event of an imperfectly registered non-white document.

Amplifier back-ground control apparatus for use in a document scanning

Growing community of inventors

Fairport, NY, United States of America

Lawrence P Lavery