Labconco Corporation

Larry G Hambleton

Elmer B Offutt

Claude L Sears

Gary P Roepke

Kevin C Gilkison

Charles A Moss

Jim Hunter

Kermit W Dyer

Yu Rich Ma

Gerald J O'Dell

A low air volume exhaust hood is based on the concept of zone laminar flow through the hood as the hood sash is raised to different levels. Laminar flow is achieved through a plurality of plenum zones constructed at the rear of the cabinet. Preferably the zones are created by utilizing different sized openings in a rear baffle of the cabinet which presents the plenum chamber. Alternatively, distinct independent plenums may be formed and coupled with a common exhaust structure. By utilizing laminar flow which is directed through different zones corresponding to different open positions of the sash, a lower volume of air can be moved through the hood while achieving desired levels of evacuation. Performance of the hood is further enhanced by a novel air foil design at the floor of the hood which promotes a sweeping flow of air across the floor. Turbulent flow is further reduced by a sash handle design which allows air to flow beneath the terminal edge of the sash at the same velocity as air entering the hood through the primary sash opening. A directional baffle for bypass air moving down the inside of the sash helps to control air flow in the upper portion of the hood.

Low air volume laboratory fume hood

A laboratory fume hood has a cabinet structure, which defines an enclosed work area, and a primary exhaust assembly. The primary exhaust assembly serves to contain fumes within the work area and then exhaust the fumes. It effects a flow of a volume of air through the work area and in many instances is designed to maintain a constant face velocity across an access opening in the front wall of the fume hood. A secondary collection device is disposed within the fume hood for removing a concentration of fumes from a small portion of the work area. The secondary collection device includes a collector head disposed in the work area and a conduit connected to the primary exhaust assembly. A portion of the air flowing through the work area is directed to the primary exhaust assembly through the secondary collection device. The volume of air passing through the secondary device should not be high enough to adversely affect the containment capabilities of the primary exhaust assembly. A blower may be provided to facilitate air flow through the secondary collector. A scrubber assembly or carbon filter assembly may be coupled with the primary exhaust assembly to purify the air collected by the secondary collection device.

Fume hood with secondary exhaust collection device

Apparatus for washing and vacuum drying long necked laboratory flasks is presented. The apparatus includes a cabinet which presents a washing and drying compartment and a pump and rotary spray arm. A special rack which can be rolled into and out of the compartment includes a central manifold and a plurality of distribution arms extending radially from the manifold. Upright spindle tubes extend from the distribution arms to receive the inverted flasks such at that the tubes extend through the narrow necks of the flasks with the open ends of the tubes located within the bodies of the flasks. A diaphragm coupling allows water to be pumped to the manifold for delivery to the spindle tubes during washing and rinsing cycles. The tubes spray the water directly inside of the flask bodies for thorough washing and rinsing. A vacuum conduit extending from the manifold carries a seat which engages a gasket to couple the manifold with a vacuum blower when the rack is moved into the cabinet. During the drying cycle, the blower applies vacuum through the manifold to the spindle tubes to draw moist air out of the flasks and replace it with drier air from the compartment. The vacuum drying system recirculates and heats the air and mixes it with dry outside air for enhanced drying of the flasks.

Method and apparatus for drying glassware

A method for washing and vacuum drying long necked laboratory flasks. The apparatus includes a cabinet which presents a washing and drying compartment and a pump and rotary spray arm. A special rack which can be rolled into and out of the compartment includes a central manifold and a plurality of distribution arms extending radially from the manifold. Upright spindle tubes extend from the distribution arms to receive the inverted flasks such at that the tubes extend through the narrow necks of the flasks with the open ends of the tubes located within the bodies of the flasks. A diaphragm coupling allows water to be pumped to the manifold for delivery to the spindle tubes during washing and rinsing cycles. The tubes spray the water directly inside of the flask bodies for thorough washing and rinsing. A vacuum conduit extending from the manifold carries a seat which engages a gasket to couple the manifold with a vacuum blower when the rack is moved into the cabinet. During the drying cycle, the blower applies vacuum through the manifold to the spindle tubes to draw moist air out of the flasks and replace said moist air with drier air from the compartment. The vacuum drying system recirculates and heats the air and mixes said air with dry outside air for enhanced drying of the flasks.

Flask washer with vacuum dry

A method and apparatus for purifying water to two different laboratory quality levels of purity, both of which are made available for dispensing. Ordinary tap water is prefiltered and treated by reverse osmosis to produce virtually salt free product water which is made available to a cabinet mounted faucet. The product water is delivered to a system of polishing cartridges which produce polished water and supply it to a special hand held dispensing gun. A recirculation pump operates to recirculate the water in the polishing system to prevent it from standing and eliminate the need for water storage. The product water is also recycled through the reverse osmosis cartridge. Some of the reject water from the RO cartridge is directed to a drain, but most of the reject water is recycled to conserve water. A microprocessor based control system monitors and displays the water quality and other conditions and generates an alarm if an abnormal condition arises.

Water purification machine

A method and apparatus for washing and vacuum drying long necked laboratory flasks. The apparatus includes a cabinet which presents a washing and drying compartment and a pump and rotary spray arm. A special rack which can be rolled into and out of the compartment includes a central manifold and a plurality of distribution arms extending radially from the manifold. Upright spindle tubes extend from the distribution arms to receive the inverted flasks such at that the tubes extend through the narrow necks of the flasks with the open ends of the tubes located within the bodies of the flasks. A diaphragm coupling allows water to be pumped to the manifold for delivery to the spindle tubes during washing and rinsing cycles. The tubes spray the water directly inside of the flask bodies for thorough washing and rinsing. A vacuum conduit extending from the manifold carries a seat which engages a gasket to couple the manifold with a vacuum blower when the rack is moved into the cabinet. During the drying cycle, the blower applies vacuum through the manifold to the spindle tubes to draw moist air out of the flasks and replace it with drier air from the compartment. The vacuum drying system recirculates and heats the air and mixes it with dry outside air for enhanced drying of the flasks.

Growing community of inventors

Olathe, KS, United States of America

Larry G Hambleton