Honda Giken Kogyo Kabushiki Kaisha

Yagi Anntena Inc.

Kazunori Kobayashi

Koji Kuroda

Takayuki Yakou

Kazuyuki Suetake

Tetsuro Hamada

Toshihiro Hosoya

Masayuki Hikita

In a container assembly for a laser diode module in which a temperature control device is not incorporated in advance, a heat-insulative casing is adapted to accommodate the laser diode module. A temperature detector is accommodated in the casing. A thermal coupling member is accommodated in the casing so as to thermally couple the laser diode module and the temperature detector. A heat-conductive plate member is attached to the casing. A heat transfer element is interposed between the thermal coupling member and the plate member so as to allow heat transfer therebetween. A sealing member is disposed between the casing and the plate member so as to seal the heat transfer element. A heat transfer controller causes the heat transfer element to control the heat transfer in accordance with a temperature of the thermal coupling member which is detected by the temperature detector.

Container assembly for laser diode module

In a four-wheel drive vehicle, a rear differential includes an input shaft to which a driving force is transmitted from front wheels through a propeller shaft, a driven bevel gear mounted on the input shaft, a follower bevel gear mounted on a clutch drive shaft and meshed with the driven bevel gear, left and right electromagnetic clutches disposed between opposite ends of the clutch drive shaft and left and right output shafts. The maximum transmitted torque transmitted through the left and right electromagnetic clutches is controlled, so that it is decreased with an increase in vehicle speed detected by vehicle speed detecting means. Thus, the vehicle can avoid the maximum horsepower transmitted by the bevel gears and the electromagnetic clutches being increased with an increase in vehicle speed. Therefore, it is possible to ensure the durability of the bevel gears and the clutches, while providing a reduction in size of the bevel gears and the clutches.

Driving force control system in four-wheel drive vehicle

A rear differential in a four-wheel drive vehicle includes a left and right clutches adapted to distribute a driving force transmitted from front wheels through a propeller shaft to left and right rear wheels. If the engagement of the left and right clutches is released, only the front wheels are driven and in this manner, the vehicle is brought into a front wheel-drive state. If the left and right clutches are brought into their engaged states, both of the front wheels and the rear wheels are driven and in this manner, the vehicle is brought into a four-wheel drive state. By changing the engagement forces of the left and right clutches, different driving forces can be distributed to the left and right rear wheels. In addition, when a driver operates a differential lock switch, the left and right clutches, are brought into their engaged states with the maximum engagement force, thereby integrally coupling the propeller shaft to the left and right rear wheels to provide a differential-locked state. Thus, a differential lock mechanism can be provided to the differential in a simple structure.

Four-wheel drive vehicle

A power transmitting system having an input shaft, a driven bevel gear, a follower bevel gear and a clutch drive shaft accommodated in longitudinally bisected center casings. Left and right electromagnetic clutches connected to the clutch drive shaft are accommodated in left and right side casings which are connected to the center casings and, such that a driving force from the input shaft is transmitted to left and right wheels through the pair of bevel gears and the left and right clutches. Thus, maintenance of the clutches can be easily performed, and the check and regulation of the meshed states of the bevel gears can be easily performed.

Power transmitting system for vehicle

A power transmitting system having an input shaft, a driven bevel gear, a follower bevel gear and a clutch drive shaft accommodated in center casings. Left and right electromagnetic clutches connected to the clutch drive shaft are accommodated in left and right side casings. Oil for lubricating the electromagnetic clutches is supplied from an oil pump accommodated in the center casings and driven by the clutch drive shaft through oil passages and axially defied in the clutch drive shaft and left and right output shafts. Thus, the length of the oil passages for supplying the oil from the oil pump to the clutches can be minimized to provide a reduction in size of the power transmitting system.

Clutch lubricating structure in power transmitting system

In a power transmitting system, a clutch drive shaft driven through bevel gears and by an input shaft is laterally extensive and left and right electromagnetic clutches are disposed between opposite ends of the clutch drive shaft and left and right output shafts, respectively. A clutch body heated during the transmission of a power is disposed at a laterally outer location of the system to provide enhanced heat-radiatability, and an annular solenoid is disposed inside the clutch body. A bearing for supporting each of the opposite ends of the clutch drive shaft is disposed radially inside the solenoid. Thus, the lateral dimension of the power transmitting system is reduced.

A solenoid of an electromagnetic clutch includes an annular coil, an annular coil housing which covers a radially facing outer peripheral surface, a radially facing inner peripheral surface and an axially facing end face of the coil. An armature is adapted to be attracted to the one end face of the coil housing by supplying an electric current to the coil. The housing axially protrudes past the other axially facing end face of the coil by a distance L. Thus, the magnetic resistance around the outer periphery of the coil is decreased to enhance the magnetic flux density of the magnetic closed circuit, thereby enabling the reliable attraction of the armature without increasing the electric power consumed by the coil.

Electromagnetic clutch

A 4-wheel drive vehicle has a driving force control method in which a portion of a driving force for front wheels is distributed to rear wheels through clutches. In a 4-wheel drive state in which a driving force T.sub.p is distributed to rear wheels, for example, if the vehicle is turned leftwards to generate a difference W.sub.R -W.sub.L between left and right rear wheel speeds, it is ensured that a driving force T.sub.R distributed to the right rear wheel, which is an outer wheel during turning of the vehicle, is larger than a driving force T.sub.L distributed to the left rear wheel, which is an inner wheel during turning of the vehicle, thereby providing an enhancement in turning performance. As the difference W.sub.R -W.sub.L between the left and right rear wheel speeds is increased as a result of decreasing of the turning radius of the vehicle, the driving force T.sub.P (=T.sub.L +T.sub.R) distributed to the rear wheels is decreased to avoid an increase in travel resistance. Thus, it is possible to prevent the occurrence of problems such as a deterioration of specific fuel consumption, an abnormal sound generated in a drive system and an increase in the load of the drive system due to an increase in travel resistance during turning of the vehicle.

Growing community of inventors

Saitama, Japan

Kazunori Kobayashi