Psemi Corporation

Murata Manufacturing Co., Ltd.

Peregrine Semiconductor Corporation

Kashish Pal

Poojan Wagh

Tero Tapio Ranta

Robert Mark Englekirk

Simon Edward Willard

Keith Bargroff

Emre Ayranci

Miles Sanner

Vikas Sharma

John Birkbeck

Mark James O'Leary

Sebastian Diebold

Phanindra Yerramilli

Daoud Salameh

Leland Gilreath

Arun Srikanth Peri

Farshid Aryanfar

Various methods and circuital arrangements for biasing one or more gates of stacked transistors of an amplifier are possible where the amplifier is configured to operate in at least an active mode and a standby mode. Circuital arrangements can reduce bias circuit standby current during operation in the standby mode while allowing a quick recovery to normal operating conditions of the amplifier. Biasing an input transistor of the stacked transistors can be obtained by using a replica stack circuit.

Standby voltage condition for fast RF amplifier bias recovery

A hybrid coupler-based T/R switch for use in a TDM system. An output hybrid coupler of a balanced amplifier is used to selectively switch a transmit or receive path to an antenna. During transmission, power at the output of the balanced amplifier is delivered directly to the antenna. During reception, power from the antenna is reflected through ports of the hybrid coupler connected to respective two amplifiers of the balanced amplifier, to constructively combine at a port of the coupler coupled to the receive path, with a ninety degrees phase shift. A pair of shunting switches or series switches coupled to the ports of the hybrid coupler connected to the two amplifiers, and a shunting switch coupled to the port coupled to the receive path, control operation of the hybrid coupler-based T/R switch. An additional switch coupled to the port of the coupler that is coupled to the receive path can provide a bypass path for reception or transmission through the antenna while bypassing the balanced amplifier of the transmit path and an amplifier of the receive path.

Hybrid coupler based T/R switch

Various methods and circuital arrangements for biasing one or more gates of stacked transistors of an amplifier are possible where the amplifier is configured to operate in at least an active mode and a standby mode. Circuital arrangements can reduce bias circuit and stacked transistors standby current during operation in the standby mode and to reduce impedance presented to the gates of the stacked transistors during operation in the active mode while maintaining voltage compliance of the stacked transistors during both modes of operation.

Gate drivers for stacked transistor amplifiers

An amplifier circuit configuration capable of processing non-contiguous intra-band carrier aggregate (CA) signals using amplifiers is disclosed herein. In some cases, each of a plurality of amplifiers is an amplifier configured as a cascode (i.e., a two-stage amplifier having two transistors, the first configured as a 'common source' input transistor, e.g., input field effect transistor (FET), and the second configured in a “common gate” configuration as a cascode output transistor, (e.g. cascode output FET). In other embodiments, the amplifier may have additional transistors (i.e., more than two stages and/or stacked transistors). The amplifier circuit configuration can be operated in either single mode or split mode. A switchable coupling is placed between the drain of the input FETs of each amplifier within the amplifier circuit configuration. During split mode, the coupling is added to the circuit to allow some of the signal present at the drain of each input FET to be coupled to the drain of the other input FET.

Drain switched split amplifier with capacitor switching for noise figure and isolation improvement in split mode

A phase shifter for altering the phase of a radio frequency signal is disclosed herein. A Lange coupler is used having reflective ports that are coupled to artificial transmission lines. The artificial transmission lines provide a reflection transmission path, the length of which can be determined by digital control lines. Transistors placed along the length of the central trace provide independent paths to ground that serve to shorten the electrical length of the ATL. Accordingly, by selectively turning the transistors on/off, the electrical length of the ATL can be selected and thus the amount of phase delay introduced by the phase shifter.

Low loss reflective passive phase shifter using time delay element with double resolution

An amplifier circuit configuration capable of processing non-contiguous intra-band carrier aggregate (CA) signals using amplifiers is disclosed herein. In some cases, each of a plurality of amplifiers is an amplifier configured as a cascode (i.e., a two-stage amplifier having two transistors, the first configured as a 'common source' input transistor, e.g., input field effect transistor (FET), and the second configured in a 'common gate' configuration as a cascode output transistor, (e.g. cascode output FET). In other embodiments, the amplifier may have additional transistors (i.e., more than two stages and/or stacked transistors). The amplifier circuit configuration can be operated in either single mode or split mode. A switchable coupling is placed between the drain of the input FETs of each amplifier within the amplifier circuit configuration. During split mode, the coupling is added to the circuit to allow some of the signal present at the drain of each input FET to be coupled to the drain of the other input FET.

Various methods and circuital arrangements for biasing gates of stacked transistors of a cascode amplifier are presented, where the amplifier is configured to operate according to different modes of operation. Such circuital arrangements operate in a closed loop with a feedback voltage that is based on a sensed voltage at one or more nodes of a replica circuit of the stacked transistors, the amplifier and the replica circuit biased with same gate voltages. According to one aspect, one gate voltage is adjusted based on a comparison of the feedback voltage with a reference voltage, and other gate voltages are derived by offsetting of the one gate voltage with voltages generated by a current flow through a resistive ladder network.

Bias techniques for controlled voltage distribution in stacked transistor amplifiers

A hybrid coupler-based T/R switch for use in a TDM system. An output hybrid coupler of a balanced amplifier is used to selectively switch a transmit or receive path to an antenna. During transmission, power at the output of the balanced amplifier is delivered directly to the antenna. During reception, power from the antenna is reflected through ports of the hybrid coupler connected to respective two amplifiers of the balanced amplifier, to constructively combine at a port of the coupler coupled to the receive path, with a ninety degrees phase shift. A pair of shunting switches coupled to the ports of the hybrid coupler connected to the two amplifiers, and a shunting switch coupled to the port coupled to the receive path, control operation of the hybrid coupler-based T/R switch.

Growing community of inventors

Reading, United Kingdom

Kashish Pal