Mitsubishi Electric Corporation

Ubukata Industries Co., Ltd.

Kanichiro Sugiura

Shinichi Takahashi

Hideaki Maeyama

Shin Sekiya

Tatsuya Sasaki

Raito Kawamura

Taro Kato

Tetsuhide Yokoyama

Kota Mizuno

Toshiaki Iwasaki

Noriaki Matsunaga

Shogo Moroe

Hiroshi Murata

Hideki Okumura

Takehiko Okumura

Yutaka Hirakawa

A pressure switch includes an airtight metallic pressure vessel. A contact mechanism is normally in a closed state and assumes an open state when a pressing force acts thereon. An airtight terminal, provided through an end surface section of the pressure vessel, is connected to the contact mechanism. A metallic first diaphragm is secured to a surface section at one end of the pressure vessel, is moved by a first moving pressure, and is reset by a reset pressure that is lower than the first moving pressure. A first plunger causes the contact mechanism to switch the open state. A metallic second diaphragm is secured to pressure vessel, is moved by a second moving pressure that is higher than the first moving pressure, and is not reset under at least an atmospheric pressure. A second plunger causes the contact mechanism to switch to the open state.

Pressure switch and hermetically sealed electric compressor

A multi-cylinder rotary compressor includes plural compression mechanism parts. A drawing force is applied to a vane of at least one of the compression mechanism parts radially outward with respect to a drive shaft, making a pressing force pressing the vane toward a piston smaller than in other compression mechanism parts. In a normal state, a pressing force due to a gas pressure difference between a suction pressure and a discharge pressure is larger than the drawing force, and a vane front end is pressed against a rotary piston peripheral wall. When the drawing force becomes greater than the pressing force, the vane front end is moved to separate from the rotary piston peripheral wall with a space through which oil is introduced from a sealed container, and a retention mechanism retains the vane separated from the piston, and the compression mechanism part switches to an uncompressed state.

Multi-cylinder rotary compressor and vapor compression refrigeration cycle system including the multi-cylinder rotary compressor

A gap between a vane tip and a cylinder inner circumferential surface is denoted by &#x3b4;. If rv is set as in an Expression (1), a first vane rotates with the vane tip thereof being out of contact with the cylinder inner circumferential surface. In the vane compressor, wear at the tip of a vane is suppressed, loss due to sliding on bearings is reduced by supporting a rotating shaft portion with a small diameter, and accuracy in an outside diameter and center of rotation of a rotor portion is increased.

Vane compressor that suppresses the wear at the tip of the vane

To allow a bush to stably rotate about a bush center, an end of a vane portion that is close to an inner circumferential surface center is always positioned on the inner side with respect to the bush center. Thereby, in a vane compressor a vane is stably supported, wear at a tip of the vane is suppressed, loss due to sliding on bearings is reduced by supporting a rotating shaft portion with a small diameter, and accuracy in outside diameter and center of rotation of a rotor portion is increased.

Vane compressor having a vane supporter that suppresses leakage of refrigerant

A vane compressor includes a cylinder, a rotor portion, vanes, and a first discharge port allowing a refrigerant in a compression chamber to be discharged therethrough. The vanes are disposed inside the rotor portion and held rotatably about the center of a cylinder inner circumferential surface, partition a space between the cylinder inner circumferential surface and the rotor portion, and form the compression chamber. A second discharge port is disposed at a location having a phase angle smaller than that at the first discharge port, being open to the cylinder inner circumferential surface, and communicating with the compression chamber. The second discharge port includes an opening portion to the compression chamber, the opening portion having a width in the circumferential direction, the width being equal to or smaller than the width of the tip of each of the vanes.

Vane compressor having a second discharge port that includes an opening portion to a compression space

A vane-type compressor includes a rotor shaft that includes rotating shaft portions and a rotor portion, which are integrated with one another. A lower end of the rotating shaft is disposed in an oil reservoir. The vane-type compressor also includes vane aligners disposed at both end portions of vanes, and recess portions, which are respectively formed in a frame and a cylinder head so as to be concentric with an inner circumferential surface of a cylinder. Outer circumferential surfaces of the vane aligners are slidably supported by the recess portions. In the rotor shaft, oil supply channels, which allow communication between the oil reservoir and the recess portions of the frame and the cylinder head, and an oil pump, which supplies refrigerating machine oil in the oil reservoir to the oil supply channels, are provided.

Vane-type compressor having an oil supply channel between the oil resevoir and vane angle adjuster

Growing community of inventors

Chiyoda-ku, Japan

Kanichiro Sugiura