Zilog, Inc.

Ixys Intl Limited

Altera Corporation

Ixys Ch Gmbh

Kamlapati Khalsa

Yefim Gluzman

Quyen Tran

Roger Ball

Kevin A Norman

David D Eaton

A multi-lamp fluorescent light fixture includes a plurality of replaceable fluorescent lamp starter units. Each starter unit has a built-in microcontroller, an RF (Radio-Frequency) receiver, and communicates wirelessly with a master unit. The plurality of starter units can be wirelessly controlled to dim the multi-lamp fixture. Each starter unit receives a DIM command. Each starter unit identified as a dimmer starter unit responds to the DIM command by turning off coupled fluorescent lamps. Starter units not identified as dimmer starter units respond by leaving coupled lamps turned on, or alternatively, turning off and quickly restarting coupled lamps. Systems of existing light fixtures are retrofitted with such wireless starter units, and thereby made controllable by a master unit so that the master unit can dim the lights if room occupancy is not detected or if sufficient ambient light is available.

Dimming a multi-lamp fluorescent light fixture by turning off an individual lamp using a wireless fluorescent lamp starter

A multi-lamp fluorescent light fixture includes a plurality of replaceable fluorescent lamp starter units. Each starter unit has a built-in microcontroller, an RF (Radio-Frequency) receiver, and communicates wirelessly with a master unit. Each starter unit can be wirelessly controlled to turn off coupled fluorescent lamps. Each starter unit receives a turn off command, monitors the AC voltage supplied to coupled lamps, and initiates turn off when the AC voltage reaches a threshold voltage stored in a memory of the microcontroller. In one novel aspect, each threshold voltage is selected such that turn off of lamps coupled to each starter is initiated within one millisecond. Systems of existing light fixtures are retrofitted with such wireless starter units, and thereby made controllable by a master unit so that the master unit can turn off the lights if room occupancy is not detected or if sufficient ambient light is available.

Turning off multiple fluorescent lamps simultaneously using RF-enabled lamp starter units

A local minimum of a current monitoring signal is identified by a starter unit that turns off a fluorescent lamp without using a wall switch. Closing a main switch in the starter unit stops an illuminating current from flowing through a gas in the lamp. The local minimum of the current monitoring signal is reached when an increasing valid sample is identified following four valid samples. A sample is valid if it does not differ from the preceding valid sample by more than a threshold difference based on known properties of the signal. By skipping invalid samples, the local minimum is accurately determined to have been reached despite transient noise spikes in the signal that would trip any voltage threshold used to locate the local minimum. When the main switch is opened at a predetermined time after the local minimum, the illuminating current does not again flow through the gas.

Rejecting noise transients while turning off a fluorescent lamp using a starter unit

A legacy-type fluorescent lamp fixture involves a magnetic ballast and a starter unit socket. Power savings are realized by using a retrofit fluorescent lamp assembly in place of the fluorescent lamp that would ordinarily by held in the fixture. The retrofit assembly may, for example, have a smaller fluorescent lamp. A digitally controlled electronic ballast within the retrofit assembly drives the smaller fluorescent lamp efficiently, thereby achieving power savings. In addition, an RF-enabled switch is installed in the starter unit socket. The RF-enabled switch communicates multi-bit digital control signals in serial fashion from the starter socket, through existing wires of the fixture, through the lamp holders of the fixture, and into the retrofit assembly. The electronic ballast receives these signals, decodes them, and in response turns on or turns off its lamp as commanded. Additional power savings are thereby achieved by keeping the lamp off when it is not needed.

Remote control of a legacy fluorescent lamp fixture

A starter unit (for example, an RF-enabled and replaceable starter unit) has an ability both to turn on and to turn off a fluorescent lamp. The starter unit detects whether a ballast in the circuit with the fluorescent lamp is of a first type (for example, an L-type ballast) or is of a second type (for example, a C-type ballast). If the determination is that the ballast is of the first type, then the starter unit turns off the lamp in a first way (for example, using C-type timing and then using L-type timing alternatingly). If the determination is that the ballast is of the second type, then the starter unit turns off the lamp in a second way (for example, using only C-type timing). The same starter unit design is usable both in single-lamp fixtures and in multi-lamp fixtures where a mix of ballast types may be used.

Alternating turn off timing of a fluorescent lamp starter unit

In a circuit that turns off a fluorescent lamp, clamping circuitry is provided to dissipate energy stored in a ballast when the lamp is being turned off. In a normal state in which the lamp is on, or in a normal state in which the lamp is off, clamping is not performed as long the VDS of a power switch is below a voltage A. In a lamp turn off operation, the switch is turned on for a time period to extinguish the lamp, and is then made to operate as a clamp (operate in its linear region) for a second period of time to dissipate energy that was stored in the ballast. Clamping in the linear region continues for VDS voltages down to B as ballast energy is dissipated, where B is smaller than A. By clamping down to the lower voltage B, re-ignition of the lamp is prevented.

Smart clamp

An alignment target for use in aligning a semiconductor wafer using a scanning light beam includes a light reflective surface of a first material such as aluminum which defines an alignment pattern and a light scattering surface of a second material abutting the light reflective surface, the light scattering surface including a raised pattern of generally orthogonal lines with the lines having inclined sidewalls which scatter impinging light. In a preferred embodiment the second material is polycrystalline silicon which has been etched to form the pattern with inclined sidewalls.

Growing community of inventors

San Jose, CA, United States of America

Kamlapati Khalsa