Conti Temic Microelectronic Gmbh

Vitesco Technologies Germany Gmbh

Jürgen Henniger

Helmut Karrer

Matthias Wieczorek

Alexander Wenk

Matthias Gramann

Bernhard Schuch

Matthias Keuten

Andreas Albert

Klaus Scharrer

Peter Guth

Uwe Trenner

Turhan Büyükbas

Jürgen Rietsch

Joachim Buhl

Andreas Schulze

Marion Gebhardt

Lisa-Maria Wittmann

Gerhard Bauer

Dirk Trodler

Roland Falkner

Andreas Vögerl

Ingrid Farnbacher

Michael Novak

Harald Oed

Daniel GÜNTHER

Christian Hirmer

Turhan BÜYÜKBAS

A control unit for use in the engine compartment or in the transmission of a motor vehicle. The control unit has a line section for an engine or transmission fluid, a circuit carrier, and a base plate. The base body is mounted on the base plate. The circuit carrier is arranged between the base body and the base plate. The base body has a plurality of parallel channels each having a respective outlet. At least one of the plurality of parallel channels forms a portion of the line section. A separate cover is mounted on the base body, the cover having a single inlet coupled to the plurality of parallel channels. The cover is, other than only the inlet, connected to the base body in a fluid-tight manner, and the inlet is the only fluid passage through the cover.

Control appliance for using in the engine compartment or in the transmission of a motor vehicle and cooling system for such a control appliance

A controller for a motor vehicle with a carrier plate for receiving a component carrier with a component carrier foot. The carrier plate has a recess through which the component carrier can be passed and which is suitable for receiving the foot, wherein the dimensions of the recess in the region of the component carrier and in the region of the foot in the X/Y-direction correspond to maximum admissible dimensions of the component carrier and of the foot () in the X/Y-direction. In the Z-direction, a pressing geometry is arranged on the recess or on the foot such that after establishing a positive-fit or non-positive connection between the carrier plate and a system interface, the pressing geometry or a part that is arranged opposite the pressing geometry is in such a deformed state that the foot is in the recess in a fixed state and without play.

Control device for a motor vehicle

A sensor arrangement has a sensor element. A contact element is in electrical contact on the one hand with the sensor element and on the other with contact pins. The contact element is insert moulded with a plastic body. Affixing positions to which the contact element has been affixed, and on which the contact element is exposed respectively have one collar made of plastic material which runs around the exposed areas of the contact element. A sensor arrangement results for which the cost of manufacture is lower than that of the prior art, while the same security against unwanted electrostatic discharging or against the formation of an unwanted short circuit remains.

Insert molded electrical contact

An arrangement of an electronic component in a plastic housing, including a cover and a lower part, and to a method for fixing the electronic component in the housing. The cover is connected to the lower part and exerts a pre-defined force (F) on the electronic component. The cover is designed such that the influence of the height tolerance (dh) of the electronic component on the force (F) can be compensated to the effect that, once the cover has been mounted, the force (F) applied to the lower part is in a pre-defined force range (B).

Housing comprising an electronic component

A housing for retaining an electronic component, including a lid and a lower part made of synthetic material, wherein the lid is joined in a force-fit manner to the lower part by clamping geometry, and in order to affix the electronic component in position, the lid applies a specified force (F) to the electronic component after being joined to the lower part due to its design. Here, the lid is designed in such a manner that the force (F) applied lies within a specified force range (B), and that the clamping geometry comprises a groove on the lower part and a ridge on the lid which grips into the groove, wherein a clamp web on the lower part or on the lid is arranged in such a manner that the lid is removably clamped to the lower part after being joined to the lower part with a force (F) which acts parallel to the clamping force (KF).

Housing comprising a device for fixing an electronic component

Growing community of inventors

Erlangen, Germany

Jürgen Henniger