Raychem Limited

Gte Automatic Electric Laboratories Incorporated

Gte Automatic Electric Labs Inc.

Joseph Zucker

Bruce D Campbell

Frank H Levinson

Arthur H Fitch

Nelson M Shen

James E Jervis

Thomas E Giles

Robert Schlingensiepen

Ralh A Narciso

Tom Call

Peder Rodhe

Campbell, Bruce D

Steve Lavelle

A strained distributed optical fiber distribution network includes read and write optical fibers having taps attached thereto in series so as to strain portions of the fiber in excess of 0.60%, the strained portions being environmentally isolated by an enclosure which includes gel filled seals subject to a resilient load.

Strained distributed optical fiber communication system

An optical fiber read or write tap includes a substrate having a substantially flat upper surface on which two separated grooves are formed, a light element being disposed in the second groove so as to be capable of coupling light with a bent portion of an optical fiber disposed in the first groove.

Distribution optical fiber tap

An optical fiber distribution network includes non-destructive read taps disposed in series which create extremely small attenuations of an optical signal being tapped, and which increase the bandwidth of an optical fiber being tapped. The network further includes non-destructive write taps disposed in another series which each inject an optical signal into a second optical fiber while inducing minimal attenuation of a preexisting optical signal in the second fiber.

Optical fiber distribution network including non-destructive taps and

A mode filter for reducing a dynamic range of a write optical fiber bus which utilizes taps which initially inject optical signals into an optical fiber which have intensities skewed towards higher order modes rather than lower order modes as compared to equilibrium for the fiber functions to preferentially attenuate outermost modes rather than lowermost modes in the fiber so as to reduce a required dynamic range for an optical receiver.

Dynamic range reduction using mode filter

A distribution optical fiber network includes a light source having a mode volume less than a distribution optical fiber, the light source being connected to the fiber so as to minimize the number and order of modes initially supported by the fiber by aligning an optical center of the light source with a geometric center of the fiber.

Bus optical fiber including low mode volume light source optimally

A method of aligning an optical signal source and a waveguide which comprises; directing the signal into the waveguide, monitoring the intensity of the signal backscattered along the waveguide, and altering the relative positions of source and waveguide in response to said intensity.

Alignment of optical waveguides

An optical fiber distribution network includes non-destructive read taps disposed in series which create extremely small attenuations of an optical signal being tapped, and which increase the bandwidth of an optical fiber being tapped. The network further includes non-destructive write taps disposed in another series which each inject an optical signal into a second optical fiber while inducing minimal attenuation of a pre-existing optical signal in the second fiber.

Optical fiber distribution network including nondestructive taps and

A method of determining splice loss 10 log (1-P.sub.R /P.sub.O) that is practiced at the location of a splice between one ends of input and output fibers. A reference level P.sub.O of light that is transmitted out of the one end of the input fiber is obtained by inserting it into an integrating cylinder of split block construction, prior to making the splice, and coupling diffuse light in the cylinder to a radiometer. After the ends of the fibers are spliced together, the splice and a significant portion of the adjacent length of output fiber exhibiting substantial leaky mode radiation that is caused by the splice, is located in the cylinder. With light of the reference level in the input fiber being incident on the splice, the radiometer provides an indication P.sub.R of light lost as a result of the splice. The indication P.sub.R may also be obtained by integrating only light radiated from a length of the leaky mode section of output fiber, which has been found to extend to approximately one foot downstream of the splice.

Method of measuring splice loss in optical fibers

A small amount of light that is transmitted in one of a pair of optical fibers having cleaved ends thereof loosely brought into butt contact is converted to leaky modes in the other fiber. Leaky mode light that is radiated out of the perimeter of the other fiber is collected in an integrating enclosure located proximate its one end and extending over a limited length of the other fiber. The light in the enclosure is detected for producing a measure of the degree of alignment of the adjacent ends of the fibers. After the cleaved ends of the fibers are aligned with micromanipulators so as to null the intensity of detected leaky mode radiation, an electrical arc is created across them for permanently joining the fiber ends together in a splice. The integrity of the resultant splice is determined by producing a measure of the splice loss 10 log (1-P.sub.R /P.sub.O), where P.sub.R is a measure of light scattered from the splice and/or radiated out of the perimeter of the leaky mode section of the other fiber for light of a radiant power P.sub.O in the one fiber and incident on the splice.

Method of splicing ends of optical fibers

Apparatus for field measurement of the insertion loss of a splice between one ends of first and second optical fibers comprises an integrating sphere that is split along its axis and which has a fiber input port, a pair of spaced-apart padded holes on the axis for receiving associated fibers so as to center the splice inside the sphere, and an output port receiving one end of a fiber bundle which couples diffuse light in the sphere to a radiometer. A baffle plate in the sphere prevents light rays from the splice being incident on the output port. The splice loss is determined by inserting the one end of the first fiber into the input port, with the other end illuminated by light from a source, and reading a reference level of light coupled to the radiometer. The two fibers are then spliced together and the splice located inside the sphere. With light of the reference level now incident on the splice, light scattered thereby is diffused in the sphere and coupled by bundle fibers to the radiometer which indicates the radiant power of scattered light. The splice loss is a function of the ratio of the indications of scattered and reference light.

Growing community of inventors

Foster City, CA, United States of America

Joseph Zucker